Anionic copolymerization of nylon 6/12: A comprehensive review.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1529, doi. 10.1002/pen.25171
- By:
- Publication type:
- Article
Works matching IS 0032-3888 AND VI 59 AND IP 8 AND DT 2019
Results: 22
1
2
Controlling properties of acrylate/epoxy interpenetrating polymer networks by premature termination of radical polymerization of acrylate.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1729, doi. 10.1002/pen.25173
- By:
- Publication type:
- Article
3
Preparation and characterization of hydrophilic temperature‐dependent polyurethane containing the grafted poly(N‐isopropylacrylamide).
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1719, doi. 10.1002/pen.25172
- By:
- Publication type:
- Article
4
The influence of the type of polypropylene and the length of the flow path on the structure and properties of injection molded parts with the weld lines.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1710, doi. 10.1002/pen.25170
- By:
- Publication type:
- Article
5
Influence of thermal annealing on mechanical properties and in vitro degradation of poly(p‐dioxanone).
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1701, doi. 10.1002/pen.25169
- By:
- Publication type:
- Article
6
Investigation of the strain‐rate‐dependent mechanical behavior of a photopolymer matrix composite with fumed nano‐silica filler.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1695, doi. 10.1002/pen.25168
- By:
- Publication type:
- Article
7
Influence of screw configuration and processing temperature on the properties of short glass fiber reinforced polypropylene composites.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1552, doi. 10.1002/pen.25153
- By:
- Publication type:
- Article
8
On the modeling and optimization of UV‐curable fluoro‐siloxane formulations and their solvent absorption and adhesion properties.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1678, doi. 10.1002/pen.25166
- By:
- Publication type:
- Article
9
Viscoelastic behavior and constitutive modeling of PP/HNT composites prepared by water‐assisted extrusion.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1585, doi. 10.1002/pen.25156
- By:
- Publication type:
- Article
10
Effect of interfacial chemistry on crystallization of polypropylene/multiwall carbon nanotube nanocomposites.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1570, doi. 10.1002/pen.25155
- By:
- Publication type:
- Article
11
Properties of microinjection‐molded polypropylene/graphite composites.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1560, doi. 10.1002/pen.25154
- By:
- Publication type:
- Article
12
Processability study of in‐mold coating for sheet molding compound compression molded parts.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1688, doi. 10.1002/pen.25167
- By:
- Publication type:
- Article
13
Relationships between crystalline structure and the thermal behavior of poly(ethylene 2,5‐furandicarboxylate): An in situ simultaneous SAXS‐WAXS study.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1667, doi. 10.1002/pen.25165
- By:
- Publication type:
- Article
14
Tough and recoverable triple‐network hydrogels based on multiple pairs of toughing mechanisms with excellent ionic conductivity as stable strain sensors.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1657, doi. 10.1002/pen.25164
- By:
- Publication type:
- Article
15
Estimates for material shrinkage in molded parts caused by time‐varying cavity pressures.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1648, doi. 10.1002/pen.25163
- By:
- Publication type:
- Article
16
Mechanical characterization of graphene oxide reinforced epoxy at different strain rates.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1636, doi. 10.1002/pen.25162
- By:
- Publication type:
- Article
17
Interface porosity in multilayered all‐conducting polymer electrodes.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1624, doi. 10.1002/pen.25160
- By:
- Publication type:
- Article
18
Synthesizing radiation‐hard polymer and copolymers using laccol monomers extracted from lacquer tree toxicodendron succedanea via cationic polymerization.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1611, doi. 10.1002/pen.25159
- By:
- Publication type:
- Article
19
Synthesis and self‐healing behavior of thermoreversible epoxy resins modified with nitrile butadiene rubber.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1603, doi. 10.1002/pen.25158
- By:
- Publication type:
- Article
20
Thermoplastic polyurethane/polytetrafluoroethylene/bridged dopo derivative composites: Flammability, thermal stability, and mechanical properties.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1593, doi. 10.1002/pen.25157
- By:
- Publication type:
- Article
21
Influence of vacuum on the porosity and mechanical properties in rotational molding.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1544, doi. 10.1002/pen.25152
- By:
- Publication type:
- Article
22
Issue Information.
- Published in:
- Polymer Engineering & Science, 2019, v. 59, n. 8, p. 1525, doi. 10.1002/pen.24920
- Publication type:
- Article