Works matching IS 20751702 AND DT 2018 AND VI 6 AND IP 2
Results: 15
Optimization of Microchannel Heat Sinks Using Prey-Predator Algorithm and Artificial Neural Networks.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 26, doi. 10.3390/machines6020026
- By:
- Publication type:
- Article
Monitoring the Oil of Wind-Turbine Gearboxes: Main Degradation Indicators and Detection Methods.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 25, doi. 10.3390/machines6020025
- By:
- Publication type:
- Article
Prediction of Thrust Force and Cutting Torque in Drilling Based on the Response Surface Methodology.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 24, doi. 10.3390/machines6020024
- By:
- Publication type:
- Article
Requirements of the Smart Factory System: A Survey and Perspective.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 23, doi. 10.3390/machines6020023
- By:
- Publication type:
- Article
UML-Based Cyber-Physical Production Systems on Low-Cost Devices under IEC-61499.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 22, doi. 10.3390/machines6020022
- By:
- Publication type:
- Article
Non-Destructive Testing for Winding Insulation Diagnosis Using Inter-Turn Transient Voltage Signature Analysis.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 21, doi. 10.3390/machines6020021
- By:
- Publication type:
- Article
On the Computational Methods for Solving the Differential-Algebraic Equations of Motion of Multibody Systems.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 20, doi. 10.3390/machines6020020
- By:
- Publication type:
- Article
Use of the Adjoint Method for Controlling the Mechanical Vibrations of Nonlinear Systems.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 19, doi. 10.3390/machines6020019
- By:
- Publication type:
- Article
Obstacle Avoidance System for Unmanned Ground Vehicles by Using Ultrasonic Sensors.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 18, doi. 10.3390/machines6020018
- By:
- Publication type:
- Article
Development of a Methodology for Condition-Based Maintenance in a Large-Scale Application Field.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 17, doi. 10.3390/machines6020017
- By:
- Publication type:
- Article
Influence of Hub Parameters on Joining Forces and Torque Transmission Output of Plastically-Joined Shaft-Hub-Connections with a Knurled Contact Surface.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 16, doi. 10.3390/machines6020016
- By:
- Publication type:
- Article
Theoretical and Experimental Studies of Over-Polishing of Silicon Carbide in Annular Polishing.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 15, doi. 10.3390/machines6020015
- By:
- Publication type:
- Article
Effects of Setting Errors (Insert Run-Outs) on Surface Roughness in Face Milling When Using Circular Inserts.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 14, doi. 10.3390/machines6020014
- By:
- Publication type:
- Article
Comparative Analysis of Machining Procedures.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 13, doi. 10.3390/machines6020013
- By:
- Publication type:
- Article
System Identification Algorithm for Computing the Modal Parameters of Linear Mechanical Systems.
- Published in:
- Machines, 2018, v. 6, n. 2, p. 12, doi. 10.3390/machines6020012
- By:
- Publication type:
- Article