Works matching IS 20668201 AND DT 2018 AND VI 10 AND IP 3
Results: 16
Nanofilled EPDM composite for aerospace applications.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 177, doi. 10.13111/2066-8201.2018.10.3.15
- By:
- Publication type:
- Article
Numerical Calculation of Wind Tip Vortex Formation for Different Wingtip devices.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 167, doi. 10.13111/2066-8201.2018.10.3.14
- By:
- Publication type:
- Article
Aerodynamic Analysis of C-Wing Aircraft.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 157, doi. 10.13111/2066-8201.2018.10.3.13
- By:
- Publication type:
- Article
Helicopter Roll-Axis Instabilities induced by Pilot Cyclic Control: A Physical Explanation.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 139, doi. 10.13111/2066-8201.2018.10.3.12
- By:
- Publication type:
- Article
MDO approach for a two-stage microlauncher.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 127, doi. 10.13111/2066-8201.2018.10.3.11
- By:
- Publication type:
- Article
Calculation of the zeros of some special functions.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 119, doi. 10.13111/2066-8201.2018.10.3.10
- By:
- Publication type:
- Article
Disturbance observer based sliding mode control for unmanned helicopter hovering operations in presence of external disturbances.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 103, doi. 10.13111/2066-8201.2018.10.3.9
- By:
- Publication type:
- Article
Analysis of isogrid reinforced cylindrical vessels in the case of axially symmetric buckling.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 89, doi. 10.13111/2066-8201.2018.10.3.8
- By:
- Publication type:
- Article
Thermal Effects on Single - Lap, Single - Bolt, Hybrid Metal - Composite Joint Stiffness.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 75, doi. 10.13111/2066-8201.2018.10.3.7
- By:
- Publication type:
- Article
3D Complex Structures through Layer Plastic Deposition Designed for Carbon Material Impregnation.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 65, doi. 10.13111/2066-8201.2018.10.3.6
- By:
- Publication type:
- Article
Preliminary Estimation Methods for the Definition of the Landing Gear.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 187, doi. 10.13111/2066-8201.2018.10.3.16
- By:
- Publication type:
- Article
A 2D description of the single crystal thin plate growth from the melt by micro- pulling- down method. Part 2.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 53, doi. 10.13111/2066-8201.2018.10.3.5
- By:
- Publication type:
- Article
A 2D description of the single crystal thin plate growth from the melt by micro - pulling - down method. Part 1.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 37, doi. 10.13111/2066-8201.2018.10.3.4
- By:
- Publication type:
- Article
Integral Method for Structural Analysis of Beams with Bending-Torsion Coupling.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 27, doi. 10.13111/2066-8201.2018.10.3.3
- By:
- Publication type:
- Article
Numerical Simulations of Flow in Axial Compressor System, Preparatory Steps for Active Control.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 15, doi. 10.13111/2066-8201.2018.10.3.2
- By:
- Publication type:
- Article
Computational Study in Centrifugal Compressor.
- Published in:
- INCAS Bulletin, 2018, v. 10, n. 3, p. 3, doi. 10.13111/2066-8201.2018.10.3.1
- By:
- Publication type:
- Article