New Simplified Low Cost Simulation Method for SME Manufacturing System.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 206, doi. 10.15866/ireme.v9i2.5765
- By:
- Publication type:
- Article
Works matching IS 19708734 AND DT 2015 AND VI 9 AND IP 2
Results: 13
1
2
Local Pool Boiling Heat Transfer on a Nearly Horizontal Tube.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 201, doi. 10.15866/ireme.v9i2.5659
- By:
- Publication type:
- Article
3
A Thermodynamic Analysis of Three and Four-Wheel Air Cycle Machines for Aeronautical Applications.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 190, doi. 10.15866/ireme.v9i2.5543
- By:
- Publication type:
- Article
4
Control Algorithm for an Industrial Robotic Arm Using Computer Vision.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 182, doi. 10.15866/ireme.v9i2.5457
- By:
- Publication type:
- Article
5
Maintenance Contractor Selection for Small Hydropower Project: a Fuzzy Multi-Criteria Optimization Technique Approach.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 174, doi. 10.15866/ireme.v9i2.5319
- By:
- Publication type:
- Article
6
Convective Condensation of Methanol Vapor in Presence of a Non-Condensable Gas with Turbulent Flow in Vertical Tube.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 167, doi. 10.15866/ireme.v9i2.5311
- By:
- Publication type:
- Article
7
Plastic Zone and Volumetric Approach-Mixed Mode Fracture I+II Emanating From Notches.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 160, doi. 10.15866/ireme.v9i2.5279
- By:
- Publication type:
- Article
8
Numerical Study of Effects of Piston Bowl Geometry on the Intake Generated Swirl in a PCCI Engine.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 154, doi. 10.15866/ireme.v9i2.5225
- By:
- Publication type:
- Article
9
Numerical and Experimental Investigation of Air-Water Two-Phase Flow in a Pipe with Three Cavities of Different Aspect Ratios.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 145, doi. 10.15866/ireme.v9i2.5216
- By:
- Publication type:
- Article
10
Optimization of Machining Parameters in AWJM Process for Lead Tin Alloy Using RSM and Regression Analysis.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 136, doi. 10.15866/ireme.v9i2.4791
- By:
- Publication type:
- Article
11
Predicting the Residual Stresses in Steel T-Section Beams Using Acoustic Emission Technique.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 129, doi. 10.15866/ireme.v9i2.4687
- By:
- Publication type:
- Article
12
Analysis of the Effect on the Mechanical Injection Engine Using Doped Diesel Fuel by Ethanol and Bio-Oil.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 124, doi. 10.15866/ireme.v9i2.4341
- By:
- Publication type:
- Article
13
Analytical and Numerical Investigations on Buckling of an Axially Compressed Cylindrical Panel with Specific Boundary Condition.
- Published in:
- International Review of Mechanical Engineering, 2015, v. 9, n. 2, p. 118, doi. 10.15866/ireme.v9i2.3315
- By:
- Publication type:
- Article