Works matching IS 19708734 AND DT 2013 AND VI 7 AND IP 3
Results: 26
Stress Intensity Factors Under Mode III Loadings.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 578
- By:
- Publication type:
- Article
Dynamic and Thermodynamic Analysis of Film-Cooling.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 570
- By:
- Publication type:
- Article
Cubic Interpolation Profile Method for Prediction of Thermal Fluid Flow through Porous Media.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 563
- By:
- Publication type:
- Article
Boring Tool Chatter Suppression Using Magneto-Rheological Fluid Damper through Regression Models.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 556
- By:
- Publication type:
- Article
Optimization of Wire-Winding and Shrink-Fit Combination in Pressure Vessel Reinforcement.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 549
- By:
- Publication type:
- Article
CFD Simulation and Experimental Investigation of Convection Heat Transfer in a Rectangular Convergent Channel with Staggered Ribs.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 541, doi. 10.15866/ireme.v7i3.3793
- By:
- Publication type:
- Article
Mechanisms for Renewable Ocean Energy Conversion.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 534
- By:
- Publication type:
- Article
Castor Dynamic Investigation.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 527
- By:
- Publication type:
- Article
A Full Scale Motorcycle Dynamic Rig.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 519
- By:
- Publication type:
- Article
Improving Warpage on Thin Shallow Parts in Two-Plate Moulds with Conformal Cooling Channels.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 512
- By:
- Publication type:
- Article
Forces and Efficiency of Cams.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 507
- By:
- Publication type:
- Article
Tool-Life Model for Ceramics through Experimental Design in High Speed Machining (HSM) of 36NiCrMo16 Steel.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 499
- By:
- Publication type:
- Article
Optimization of Surface Roughness in Wet Turning Operation of High Carbon High Chromium Steel.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 495
- By:
- Publication type:
- Article
Energy Saving in the Hydraulic Cylinders by Using Novel Self-Actuated Flow Control Valve (SAFCV).
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 487
- By:
- Publication type:
- Article
Numerical Simulation of Capillary Pump Evaporator Using Water for Different Inclination Angles.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 479
- By:
- Publication type:
- Article
Modelling and Control Design of a Magnetorheological Fluid Brake.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 474
- By:
- Publication type:
- Article
Multi Characteristic Optimization in Wire Cut EDM by Using Taquchi Data Envelopment Analysis Based Ranking Methodology.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 468
- By:
- Publication type:
- Article
Optimizing the Compression Ratio of C.I Engine Fuelled in Sardine Oil Ethyl Ester.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 463
- By:
- Publication type:
- Article
Optimization of the Plastic Injection Molding Parameters for Sport Equipment by Using Design of Experiment.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 453
- By:
- Publication type:
- Article
Effect of Nanofluid Variable Properties on Natural Convection in a Square Cavity Using Lattice Boltzmann Method.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 442
- By:
- Publication type:
- Article
Dynamic Characteristic Analysis on Half Car Electro Pneumatic Suspension System.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 436
- By:
- Publication type:
- Article
Review of Material Used in Brake Pads.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 425
- By:
- Publication type:
- Article
Effect of Road Excitation on the Vehicle Vibrations Suspended by Electro-Rheological Damper.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 408
- By:
- Publication type:
- Article
Implementation of Penalty Method for Optimization of FGM Beams.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 402
- By:
- Publication type:
- Article
Engine Mapping for Improvement in Fuel Efficiency of Two Stroke SI Engine.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 392
- By:
- Publication type:
- Article
The Control of the Handling of a Front Wheel Drive Vehicle by Means of a Magnetorheological Differential.
- Published in:
- International Review of Mechanical Engineering, 2013, v. 7, n. 3, p. 395
- By:
- Publication type:
- Article