Works matching IS 19708734 AND DT 2010 AND VI 4 AND IP 1
Results: 16
A Drift-Flux Model-Based Experimental Method of Predicting the Slug-Churn Transition in Two-Phase Flow.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 65
- By:
- Publication type:
- Article
Wear and Machinability Study of SiCe Reinforced and Al<sub>2</sub>O<sub>3p</sub> Reinforced Al-Si Alloy Composites.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 28
- By:
- Publication type:
- Article
The Effect of Particulate Reinforcement Addition to Latent Heat and Solid Fraction During Solidification of Titanium Carbide Particulates Reinforced Aluminium Alloy Matrix Composite Produced by Vortex Mixing-Sand Casting Technique.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 12
- By:
- Publication type:
- Article
Interfacial Treatment of Multi-Layer Woven Silk/Epoxy Composites.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 1
- By:
- Publication type:
- Article
Heat Treatment, Wear Behaviour and Manufacturing Mode of AISI M4 High Speed Tool Steel.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 7
- By:
- Publication type:
- Article
In-Plane Free Vibrations of Annular Elliptic and Circular Elastic Plates of Non-Uniform Thickness under Classical Boundary Conditions.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 112
- By:
- Publication type:
- Article
SharE -- An Engineering System Concept Proposal for Sustainable Personal Mobility.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 106
- By:
- Publication type:
- Article
Stress Analysis a Functionally Graded Quadrangle Plate Using Second Order Shear Deformation Theory.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 92
- By:
- Publication type:
- Article
Constructal Design of Mechanisms.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 85
- By:
- Publication type:
- Article
Optimization of Mach Number for Suction and Discharge Port Areas of the Valve Plate of Hermetic Compressor Using R-410A Refrigerant Blend for A/C Application.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 80
- By:
- Publication type:
- Article
Poppet Valve Parameter Optimization of a High Frequency Operating Pump System.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 71
- By:
- Publication type:
- Article
Spatio-Temporal Identification of a Heat Source in a Diffusive by Solving a Reverse Problem.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 60
- By:
- Publication type:
- Article
Evaluation of Turbulence Models in Predicting Turbulence Penetration into Low Reynolds Number Regions.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 51
- By:
- Publication type:
- Article
An Investigation into the Friction Aided Deep Drawing Using Four and Eight Tapered Segments Blank Holder.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 42
- By:
- Publication type:
- Article
Contribution of Fatigue Behaviour of Bituminous Mixes: Comparative Study between Morocco and Japan.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 35
- By:
- Publication type:
- Article
A Study of a Stratified Plate Subject to an Impact -The Law of Penetration–.
- Published in:
- International Review of Mechanical Engineering, 2010, v. 4, n. 1, p. 18
- By:
- Publication type:
- Article