Works matching IS 19708734 AND DT 2007 AND VI 1 AND IP 3
Results: 18
Smoke Prediction for Turbocharged DI Diesel Engine During Free Acceleration.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 323
- By:
- Publication type:
- Article
Acoustic Radiation Through Double Sandwich Panels System.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 313
- By:
- Publication type:
- Article
Finite Volume Analysis of a Wire-on-Tube Heat Exchanger Used for Cooling of Electronics.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 304
- By:
- Publication type:
- Article
Modulation of the Rotor-Stator Interactions due to Clocking.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 293
- By:
- Publication type:
- Article
Two Dimensional Simulation of Incompressible Fluid Flow Using Lattice Boltzmann Method.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 286
- By:
- Publication type:
- Article
Effect of the Thermomechanical Treatment on the Springback During a Forming.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 280
- By:
- Publication type:
- Article
Study of a Thermal Ionization Source for a Cs+ Ion Probe: Modeling and Simulations Towards an Optimization of the Design.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 273
- By:
- Publication type:
- Article
Corelation Between Aluminum Alloys Oxidation and Chamber Geometry of the Heat Treatment Equipment.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 268
- By:
- Publication type:
- Article
Mechanical and Tribological Characterization of a Composite Ceramics Al<sub>2</sub>O<sub>3</sub>-ZrO<sub>2</sub>-3Al<sub>2</sub>O<sub>3</sub>+2SiO<sub>2</sub>.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 262
- By:
- Publication type:
- Article
Study of SnO<sub>2</sub> Thin Film Deposited on Soda-lime Glass Using the Spray Pyrolysis Coating Method.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 257
- By:
- Publication type:
- Article
In Optimizing CBN 7050 Lifetime During Hard Turning.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 250
- By:
- Publication type:
- Article
Wear Study of Cast Metal-on-Metal Bearing in Total Hip Prosthesis.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 245
- By:
- Publication type:
- Article
Cutting Speed Optimization in High Speed Turning.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 237
- By:
- Publication type:
- Article
Optimization of the Conditions of Machining Based on a Criterion Combined by Genetic Algorithms.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 232
- By:
- Publication type:
- Article
Some Explicit Beam, Plate and Shell Finite Elements.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 225
- By:
- Publication type:
- Article
Optimum Dynamic Performance of a Tank-Vehicle.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 218
- By:
- Publication type:
- Article
Characterization and Experimental Validation of the Dynamic Behavior of the Structure Support of an Industrial Turbo-alternator.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 207
- By:
- Publication type:
- Article
Possibilities of Exact Grinding of Conical and Globoid Worms.
- Published in:
- International Review of Mechanical Engineering, 2007, v. 1, n. 3, p. 200
- By:
- Publication type:
- Article