Works matching IS 19395981 AND DT 2019 AND VI 13 AND IP 2
Results: 24
From The Editor.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 233, doi. 10.1007/s40962-019-00324-1
- By:
- Publication type:
- Article
Metalcasting Industry Research.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 479, doi. 10.1007/s40962-019-00320-5
- Publication type:
- Article
Effects of Amplitude of Die Vibration on Cast Structure of Al4.5Cu Alloy.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 438, doi. 10.1007/s40962-018-0271-y
- By:
- Publication type:
- Article
Friction Stir Processing of Aluminum Alloy A206: Part II—Tensile and Fatigue Properties.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 244, doi. 10.1007/s40962-018-0268-6
- By:
- Publication type:
- Article
Phase Evolution of β-Al<sub>5</sub>FeSi During Recycling of Al–Si–Fe Alloys by Mg Melt.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 473, doi. 10.1007/s40962-018-0279-3
- By:
- Publication type:
- Article
Thermal Analysis of Rare Earth Grain Refined 4130.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 273, doi. 10.1007/s40962-018-0274-8
- By:
- Publication type:
- Article
Understanding the Role of Inclusions on the Dynamic Fracture Toughness of High Strength Lightweight FeMnAl Steels.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 286, doi. 10.1007/s40962-018-0273-9
- By:
- Publication type:
- Article
Effect of Pouring Conditions and Gating System Design on Air Entrainment During Mold Filling.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 255, doi. 10.1007/s40962-018-0272-x
- By:
- Publication type:
- Article
Quality Index of Tensile Properties on Microporosity Variation in A5052 Aluminium Alloy.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 450, doi. 10.1007/s40962-018-0276-6
- By:
- Publication type:
- Article
Reducing Shrinkage Porosity in High-Performance Steel Castings: Case of an ASME B16.34 Gate Valve Body: Part 2—Simulation and Experimental Verification.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 463, doi. 10.1007/s40962-018-0275-7
- By:
- Publication type:
- Article
Effects of Different Parameters on Porosity Defects Between the Horizontal and Vertical Shot Sleeve Processes.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 417, doi. 10.1007/s40962-018-0267-7
- By:
- Publication type:
- Article
Effects of Al–Ti–C–Ce Master Alloy on Microstructure and Mechanical Properties of Hypoeutectic Al–7%Si Alloy.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 426, doi. 10.1007/s40962-018-0266-8
- By:
- Publication type:
- Article
Optimizing Morphology of Primary Carbides and Mechanical Properties during Processing of Cast-Cold Work AISI D2-Steel Press Forming Dies.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 337, doi. 10.1007/s40962-018-0256-x
- By:
- Publication type:
- Article
Revealing the As-Cast and Homogenized Microstructures of Niobium-Bearing Nickel-Based Superalloy.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 320, doi. 10.1007/s40962-018-0255-y
- By:
- Publication type:
- Article
Effect of Alloy Composition on Microstructure and Tensile Properties of Net-Shaped Castings of Al–Zn–Mg–Cu Alloys.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 300, doi. 10.1007/s40962-018-0254-z
- By:
- Publication type:
- Article
A Comparative Study on Titanium-Reinforced Aluminium Matrix Composites Produced by Melt Infiltration Casting and Squeeze Infiltration.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 311, doi. 10.1007/s40962-018-0253-0
- By:
- Publication type:
- Article
Influences of Rod Diameter and Sand-Mould Strength on Hot Tearing in Mg WE43A Constrained Rod Castings.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 407, doi. 10.1007/s40962-018-0265-9
- By:
- Publication type:
- Article
Parameter Optimization of Gas Tungsten-Arc Repair Welding Technique in Mg–6Gd–3Y–0.5Zr Alloy.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 345, doi. 10.1007/s40962-018-0257-9
- By:
- Publication type:
- Article
Characterization and Microhardness Evaluation of A356/Mg Joint Produced by Vacuum-Assisted Sand Mold Compound Casting Process.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 392, doi. 10.1007/s40962-018-0264-x
- By:
- Publication type:
- Article
Friction Stir Processing of Aluminum Alloy A206: Part I—Microstructure Evolution.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 234, doi. 10.1007/s40962-018-0263-y
- By:
- Publication type:
- Article
Microstructure and Mechanical Properties of an AlN/Mg–Al Composite Synthesized by Al–AlN Master Alloy.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 384, doi. 10.1007/s40962-018-0261-0
- By:
- Publication type:
- Article
Optimisation of Dry Sliding Wear Parameters of Squeeze Cast AA336 Aluminium Alloy: Copper-Coated Steel Wire-Reinforced Composites by Response Surface Methodology.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 354, doi. 10.1007/s40962-018-0258-8
- By:
- Publication type:
- Article
Effect of Ce Inoculation on Microstructure and Mechanical Properties of in situ Al–20%Mg<sub>2</sub>Si Composite.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 331, doi. 10.1007/s40962-018-0252-1
- By:
- Publication type:
- Article
Modification of Hypereutectic Al–20 wt%Si Alloy Based on the Addition of Yttrium and Al–5Ti–1B Modifiers Mixing Melt.
- Published in:
- International Journal of Metalcasting, 2019, v. 13, n. 2, p. 367, doi. 10.1007/s40962-018-0242-3
- By:
- Publication type:
- Article