Metalcasting Industry Research.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 658, doi. 10.1007/s40962-018-0239-y
- Publication type:
- Article
Works matching IS 19395981 AND DT 2018 AND VI 12 AND IP 3
Results: 24
1
2
From the Editor.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 425, doi. 10.1007/s40962-018-0235-2
- By:
- Publication type:
- Article
3
Light Metals Alliance: Light Metals Technology 2017 Special Section.
- Published in:
- 2018
- Publication type:
- Conference Paper/Materials
4
Effect of Titanium Levels on the Hot Tearing Sensitivity and Abnormal Grain Growth After T4 Heat Treatment of Al-Zn-Mg-Cu Alloys.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 457, doi. 10.1007/s40962-018-0227-2
- By:
- Publication type:
- Article
5
Metallurgical Aspects of Inclusion Assessment in Al-6%Si Casting Alloy Using the LiMCA Technique.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 643, doi. 10.1007/s40962-017-0203-2
- By:
- Publication type:
- Article
6
Counter-Gravity Sand Casting of Steel with Pressurization During Solidification.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 596, doi. 10.1007/s40962-017-0200-5
- By:
- Publication type:
- Article
7
Effect of Ca on the Y Content and Cyclic Oxidation Behavior of Ni-Based Single-Crystal Superalloy.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 607, doi. 10.1007/s40962-017-0198-8
- By:
- Publication type:
- Article
8
Effect of Degassing and Grain Refinement on Hot Tearing Tendency in Al8Si3Cu Alloy.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 589, doi. 10.1007/s40962-017-0197-9
- By:
- Publication type:
- Article
9
Effects of Addition of Transition Metals on Intermetallic Precipitation in Al-2%Cu-1%Si-Based Alloys.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 574, doi. 10.1007/s40962-017-0196-x
- By:
- Publication type:
- Article
10
Effect of Cooling Rate on the Mechanical Properties of AA365 Aluminum Alloy Heat-Treated Under T4, T5, and T6 Conditions.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 449, doi. 10.1007/s40962-017-0195-y
- By:
- Publication type:
- Article
11
Effects of Electromagnetic Frequency and SiC Nanoparticles on the Microstructure Refinement and Mechanical Properties of Al A357-1.5 wt% SiC Nanocomposites.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 565, doi. 10.1007/s40962-017-0194-z
- By:
- Publication type:
- Article
12
Effect of Samarium (Sm) Addition on the Microstructure and Tensile Properties of Al-20%Si Casting Alloy.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 554, doi. 10.1007/s40962-017-0193-0
- By:
- Publication type:
- Article
13
AlSi5Mg0.3 Alloy for the Manufacture of Automotive Wheels.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 614, doi. 10.1007/s40962-017-0191-2
- By:
- Publication type:
- Article
14
Experimental Investigation and Optimization of Process Parameters for Impact Strength of Compound Cast Bimetallic Joints.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 498, doi. 10.1007/s40962-017-0190-3
- By:
- Publication type:
- Article
15
Effects of Process Related Variations on Fillablity Simulation of Thin-Walled IN718 Structures.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 543, doi. 10.1007/s40962-017-0189-9
- By:
- Publication type:
- Article
16
Simulation of Fluidity and Misrun Prediction for the Casting of 356.0 Aluminum Alloy into Sand Molds.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 514, doi. 10.1007/s40962-017-0188-x
- By:
- Publication type:
- Article
17
Microstructure and Tribological Characteristics of Strain-Induced Melt Activation (SIMA)-Processed Al-10Cu-Fe alloy.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 523, doi. 10.1007/s40962-017-0187-y
- By:
- Publication type:
- Article
18
Effect of Process Parameters on Distortion and Residual Stress of High-Pressure Die-Cast AZ91D Components.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 487, doi. 10.1007/s40962-017-0186-z
- By:
- Publication type:
- Article
19
The Role of Zn Additions on the Microstructure and Mechanical Properties of Mg-Nd-Zn Alloys.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 428, doi. 10.1007/s40962-017-0174-3
- By:
- Publication type:
- Article
20
Effect of Silicon and Microstructure on Spheroidal Graphite Cast Iron Thermal Conductivity at Elevated Temperatures.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 480, doi. 10.1007/s40962-017-0184-1
- By:
- Publication type:
- Article
21
Inclusion Measurements in Al-Si Foundry Alloys Using Qualiflash and Prefil Filtration Techniques.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 625, doi. 10.1007/s40962-017-0185-0
- By:
- Publication type:
- Article
22
Complexities in the Assessment of Melt Quality.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 441, doi. 10.1007/s40962-017-0179-y
- By:
- Publication type:
- Article
23
Effect of Co and Ni Addition on the Microstructure and Mechanical Properties at Room and Elevated Temperature of an Al-7%Si Alloy.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 434, doi. 10.1007/s40962-017-0178-z
- By:
- Publication type:
- Article
24
Dimensional Control of Nickel-Based Single Crystal Turbine Blade Investment Casting by Process Control Optimization.
- Published in:
- International Journal of Metalcasting, 2018, v. 12, n. 3, p. 469, doi. 10.1007/s40962-017-0180-5
- By:
- Publication type:
- Article