Usage of the Cast Iron Cylindrical Liner in an Automobile Engine Block.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 159, doi. 10.24425/afe.2024.149284
- By:
- Publication type:
- Article
Works matching IS 18973310 AND DT 2024 AND VI 24 AND IP 2
Results: 20
1
2
Corrosion of Pure Magnesium and Binary Magnesium Alloy in Ringer's Solution.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 151, doi. 10.24425/afe.2024.149283
- By:
- Publication type:
- Article
3
Research of Casting and Solidification of Steel Ingots by Application of Low-Melting Materials.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 143, doi. 10.24425/afe.2024.149282
- By:
- Publication type:
- Article
4
Impact of Aging Time on the Metallurgical Properties and Hardness Characteristics of an Al-Si-Mg-Cr Hypoeutectic Alloy Intended for Automotive Applications.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 137, doi. 10.24425/afe.2024.149281
- By:
- Publication type:
- Article
5
Analysis of Fragmentation Phenomenon of Composite Layers of Fe-TiC Type Obtained "in situ" in Steel Casting.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 131, doi. 10.24425/afe.2024.149280
- By:
- Publication type:
- Article
6
Influence of the Rate of Cooling/Solidification on the Location of Characteristic Points on the AT and ADT Curves of Cast Iron.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 124, doi. 10.24425/afe.2024.149279
- By:
- Publication type:
- Article
7
Bio-regeneration for Sodium Silicate Used Sands and its Unattended Monitoring System.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 117, doi. 10.24425/afe.2024.149278
- By:
- Publication type:
- Article
8
Study on Mn Volatilization Behavior During Vacuum Melting of High-manganese Steel.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 110, doi. 10.24425/afe.2024.149277
- By:
- Publication type:
- Article
9
Decarbonization of Production Systems in Foundries.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 103, doi. 10.24425/afe.2024.149276
- By:
- Publication type:
- Article
10
The use of Selected Lean Management Tools for Analyzing Defects in Pistons for Internal Combustion Engines.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 44, doi. 10.24425/afe.2024.149270
- By:
- Publication type:
- Article
11
Exploration and Improvement of Room Temperature Properties for Organosilicon Slag Riser.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 35, doi. 10.24425/afe.2024.149269
- By:
- Publication type:
- Article
12
The Technique of Inorganic Core Sand Shooting with Reduced Pressure in Venting System.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 98, doi. 10.24425/afe.2024.149275
- By:
- Publication type:
- Article
13
Calculations of Non-Metallic Particles Removal from Liquid Aluminium to Top Slag.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 60, doi. 10.24425/afe.2024.149272
- By:
- Publication type:
- Article
14
Microstructure and Mechanical Properties of the EN AC-AlSi12CuNiMg Alloy and AlSi Composite Reinforced with SiC Particles.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 49, doi. 10.24425/afe.2024.149271
- By:
- Publication type:
- Article
15
The Analysis of Influence of Compression Forces on the Strength of MM „Stahl 1018” Composite with the use of SolidWorks Software.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 25, doi. 10.24425/afe.2024.149268
- By:
- Publication type:
- Article
16
Synthesis and Characterization of Novel Aluminum Composites: A Compo-Casting Approach with ZrO<sub>2</sub>, Al<sub>2</sub>O<sub>3</sub>, and SiC.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 88, doi. 10.24425/afe.2024.149274
- By:
- Publication type:
- Article
17
Properties of Casting Al-Cu Alloy Modified by Mixed Rare Earth (La, Ce) and its Mechanism Analyzed.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 69, doi. 10.24425/afe.2024.149273
- By:
- Publication type:
- Article
18
Analysis of Influence of Sand Matrix on Properties of Moulding Compounds Made with Furan Resin Intended for 3D Printing.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 17, doi. 10.24425/afe.2024.149267
- By:
- Publication type:
- Article
19
Effect of Matrix Type on Properties of Moulding Sand with Barley Malt.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 11, doi. 10.24425/afe.2024.149266
- By:
- Publication type:
- Article
20
Influence of Cold Work on the Efficiency of Vibratory Machining.
- Published in:
- Archives of Foundry Engineering, 2024, v. 24, n. 2, p. 5, doi. 10.24425/afe.2024.149265
- By:
- Publication type:
- Article