Erratum to "RANS-based CFD methodology and modeling of a 1/100 scale thermoelectric power generation system for container ships".
- Published in:
- 2025
- By:
- Publication type:
- Correction Notice
Works matching IS 1738494X AND DT 2025 AND VI 39 AND IP 2
Results: 42
1
2
Erratum to "Elucidation of aerodynamic characteristics due to ice accretion on multi-mw wind turbine blade".
- Published in:
- 2025
- By:
- Publication type:
- Correction Notice
3
Performance simulation of the indoor unit of a heat pump with low-GWP alternative refrigerants.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 997, doi. 10.1007/s12206-025-0141-5
- By:
- Publication type:
- Article
4
Orientation effects of curved finned cylinders under natural convection.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 983, doi. 10.1007/s12206-025-0140-6
- By:
- Publication type:
- Article
5
Investigating the relationship between heating value and combustion/emissions and residual gas in a small spark-ignition engine powered by pure propane.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 971, doi. 10.1007/s12206-025-0139-z
- By:
- Publication type:
- Article
6
Experimental study and machine learning prediction of frost characteristics on inclined cold plates.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 957, doi. 10.1007/s12206-025-0137-1
- By:
- Publication type:
- Article
7
Effect of composition of the matching layer, directivity, temperature and pressure on ultrasonic signals in the tank.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 949, doi. 10.1007/s12206-025-0136-2
- By:
- Publication type:
- Article
8
Research on variable stiffness robotic joint actuator based on shape memory alloy.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 939, doi. 10.1007/s12206-025-0135-3
- By:
- Publication type:
- Article
9
Design and characteristics study of cantilevered assembly robot with dual passive compliance features.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 925, doi. 10.1007/s12206-025-0134-4
- By:
- Publication type:
- Article
10
Design, evaluation, and optimization of a novel 3UPU-S parallel mechanism with three rotational degrees of freedom.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 913, doi. 10.1007/s12206-025-0133-5
- By:
- Publication type:
- Article
11
Calibration of link-type counterbalance mechanism attached to a robot arm.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 905, doi. 10.1007/s12206-025-0132-6
- By:
- Publication type:
- Article
12
Trajectory tracking control of 6-UPS type parallel robots combining RBFNN and UNDO.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 891, doi. 10.1007/s12206-025-0131-7
- By:
- Publication type:
- Article
13
A novel task-space based motion planning method for redundant manipulators with trap detection.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 877, doi. 10.1007/s12206-025-0130-8
- By:
- Publication type:
- Article
14
A model-free decoupled and robust repetitive controller for trajectory tracking performance of a three-axis parallel mechanism.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 857, doi. 10.1007/s12206-025-0129-1
- By:
- Publication type:
- Article
15
Research on the reliability and sensitivity of positioning accuracy of loading manipulator based on co-simulation.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 847, doi. 10.1007/s12206-025-0128-2
- By:
- Publication type:
- Article
16
Optimization method for spiral bevel and hypoid gears with sinusoidal blade profile parameters for low impact.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 835, doi. 10.1007/s12206-025-0127-3
- By:
- Publication type:
- Article
17
Measurement uncertainty assessment of positioning error and its effects on machining error.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 821, doi. 10.1007/s12206-025-0126-4
- By:
- Publication type:
- Article
18
Digital twin modeling and simulation method for production line equipment units.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 805, doi. 10.1007/s12206-025-0125-5
- By:
- Publication type:
- Article
19
Predicting and optimizing network recognition time: a multi-parameter fusion model for edge-side human behavior recognition.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 795, doi. 10.1007/s12206-025-0124-6
- By:
- Publication type:
- Article
20
On the mechanism of the post buckling and the initiation of a propagating buckle in sandwich pipelines based on shear deformation theory.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 777, doi. 10.1007/s12206-025-0122-8
- By:
- Publication type:
- Article
21
Homogenization using lattice spring models for couple stress theory under plane strain deformation.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 767, doi. 10.1007/s12206-025-0121-9
- By:
- Publication type:
- Article
22
A new semi-analytical slice model for elastic contact analysis of herringbone gears.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 757, doi. 10.1007/s12206-025-0120-x
- By:
- Publication type:
- Article
23
Real tooth surface reconstruction and meshing characteristics analysis of variable hyperbolic circular-arc-tooth-trace cylindrical gear.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 743, doi. 10.1007/s12206-025-0119-3
- By:
- Publication type:
- Article
24
Rolling force modeling based on neural network and mechanism model.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 729, doi. 10.1007/s12206-025-0118-4
- By:
- Publication type:
- Article
25
Phase-based design method for meta-beam with achromatic wave focusing.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 717, doi. 10.1007/s12206-025-0117-5
- By:
- Publication type:
- Article
26
Gyro drift-adjusting screw mass prediction based on VGAE-SGAE algorithm.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 701, doi. 10.1007/s12206-025-0116-6
- By:
- Publication type:
- Article
27
Numerical simulations of bubble condensation under a wall effect in a subcooled liquid flow.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 687, doi. 10.1007/s12206-025-0115-7
- By:
- Publication type:
- Article
28
Investigation of effective design and application of vortex generators for the wind turbine blades.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 671, doi. 10.1007/s12206-025-0114-8
- By:
- Publication type:
- Article
29
Experimental study of ultrasound-assisted alkaline water electrolysis for hydrogen production.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 663, doi. 10.1007/s12206-025-0113-9
- By:
- Publication type:
- Article
30
Upcycling of wasted fabrics into savonius wind turbine rotor and experimental validation of design modifications for performance enhancement by wind tunnel test.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 651, doi. 10.1007/s12206-025-0112-x
- By:
- Publication type:
- Article
31
Design and structural safety evaluation of an ultra-high-pressure hydrogen vessel (type I) with maximum capacity.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 637, doi. 10.1007/s12206-025-0111-y
- By:
- Publication type:
- Article
32
Research on axial force distribution at the root of 94-meter wind turbine blades.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 627, doi. 10.1007/s12206-025-0110-z
- By:
- Publication type:
- Article
33
Mechanical behavior of 60 kV HV XLPE insulation under thermal aging and cross-correlation assessment of degradation mechanisms.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 611, doi. 10.1007/s12206-025-0109-5
- By:
- Publication type:
- Article
34
Experimental and computational studies on characteristics of indigenously produced novel Aegle marmelos micro polymer reinforced aluminum composites using powder metallurgy.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 587, doi. 10.1007/s12206-025-0108-6
- By:
- Publication type:
- Article
35
Erosion in steam turbines: A comprehensive bibliometric and systematic review unveiling cutting-edge technologies.
- Published in:
- 2025
- By:
- Publication type:
- Literature Review
36
Prediction of hypervelocity impact performance of composite protective structures using a combined finite element method and smoothed particle hydrodynamics approaches.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 553, doi. 10.1007/s12206-025-0105-9
- By:
- Publication type:
- Article
37
Modification of the structure dynamic model for spiral bevel gear based on modal experiment.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 531, doi. 10.1007/s12206-025-0104-x
- By:
- Publication type:
- Article
38
Inverse design of ventilated acoustic resonators using a sound transmission loss-encoded variational autoencoder.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 509, doi. 10.1007/s12206-025-0103-y
- By:
- Publication type:
- Article
39
CycleGAN denoising of recurrence plots of rolling bearing vibration signals for improved fault classification.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 497, doi. 10.1007/s12206-025-0102-z
- By:
- Publication type:
- Article
40
Modeling and performance analysis of a hydraulically interconnected suspension for tri-axle mining dump trucks considering pitch-roll resistance.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 483, doi. 10.1007/s12206-025-0101-0
- By:
- Publication type:
- Article
41
Tool wear prediction based on xLSTM combined with the ECA attention mechanism model.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 519, doi. 10.1007/s12206-024-1211-9
- By:
- Publication type:
- Article
42
Development of machine learning models for material classification and prediction of mechanical properties of FDM 3D printing outputs.
- Published in:
- Journal of Mechanical Science & Technology, 2025, v. 39, n. 2, p. 541, doi. 10.1007/s12206-024-1114-9
- By:
- Publication type:
- Article