Enhancement of bending toughness for Fe-based amorphous nanocrystalline alloy with deep cryogenic-cycling treatment.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 99, doi. 10.1007/s41230-024-4096-4
- By:
- Publication type:
- Article
Works matching IS 16726421 AND DT 2025 AND VI 22 AND IP 1
Results: 12
1
2
Influence of surface layer slurry temperature on surface cracks and holes of ZTC4 titanium alloy by investment casting.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 90, doi. 10.1007/s41230-025-3157-7
- By:
- Publication type:
- Article
3
New poly-types of LPSO structures in a non-equilibrium Mg<sub>97</sub>Zn<sub>1</sub>Y<sub>1.6</sub>Ca<sub>0.4</sub> alloy.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 83, doi. 10.1007/s41230-024-4036-3
- By:
- Publication type:
- Article
4
Achieving further refinement of grain structure and improvement of mechanical properties in Al-12Si-4Cu-2Ni-1Mg alloy by Al-Ti-C-B master alloy addition and deep cryogenic treatment.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 75, doi. 10.1007/s41230-024-4124-4
- By:
- Publication type:
- Article
5
Positive effect of Mo on mechanical properties of a Ni-42W-10Co-xMo medium heavy alloy.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 108, doi. 10.1007/s41230-025-4039-8
- By:
- Publication type:
- Article
6
Effect of pouring time on microstructure and mechanical properties of centrifugal cast Ti-46Al alloy tubes.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 65, doi. 10.1007/s41230-025-3171-9
- By:
- Publication type:
- Article
7
Effect of lanthanum on microstructure of a nickel-based single crystal superalloy.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 55, doi. 10.1007/s41230-025-4006-4
- By:
- Publication type:
- Article
8
Numerical simulation of microstructure and microporosity morphology in directional solidification of aluminum-copper alloys: Effect of copper content and withdrawal rate.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 33, doi. 10.1007/s41230-024-4014-9
- By:
- Publication type:
- Article
9
Prediction of intrusive gas pores caused by resin burning in sand core for iron castings.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 23, doi. 10.1007/s41230-024-4091-9
- By:
- Publication type:
- Article
10
Review of rare earth oxide doping-modified laser cladding of Fe-based alloy coatings.
- Published in:
- 2025
- By:
- Publication type:
- Literature Review
11
B2-CuZr reinforced amorphous alloy matrix composites: A review.
- Published in:
- 2025
- By:
- Publication type:
- Literature Review
12
Abrasive wear behavior of functionally graded Al<sub>3</sub>Ti reinforced aluminum matrix composite.
- Published in:
- China Foundry, 2025, v. 22, n. 1, p. 45, doi. 10.1007/s41230-024-3147-1
- By:
- Publication type:
- Article