COLOR DESIGN BASED ON KANSEI ENGINEERING AND INTERACTIVE GENETIC ALGORITHM.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 12
- By:
- Publication type:
- Article
Works matching IS 15837904 AND DT 2017 AND VI 15 AND IP 3
Results: 20
1
2
REALIZATION OF AUTOMATIC CONVEYING LINE OF WIRE HARNESS TRAY BASED ON PLC.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 92
- By:
- Publication type:
- Article
3
OPTIMIZATION OF SUSPENSION PARAMETERS BASED ON VEHICLE ROLL STABILITY AND ROAD FRIENDLINESS.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 84
- By:
- Publication type:
- Article
4
FAULT DIAGNOSIS METHODOF MECHANICAL HYDRAULIC SYSTEM BASED ON ARTIFICIAL INTELLIGENCE.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 55
- By:
- Publication type:
- Article
5
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS IN THE CASE OF TURNING OF FREE-CUTTING STEEL AUT20 (22S20).
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 49
- By:
- Publication type:
- Article
6
THE APPLICATION OF DATA-PROCESS INTERACTION MODEL IN COST ALLOCATION.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 129
- By:
- Publication type:
- Article
7
STUDY ON THE PREPARATION OF COLUMN-CELL AND ITS INFLUENCE ON MECHANICAL PROPERTIES BY DEEP DRAWING.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 119
- By:
- Publication type:
- Article
8
SIMULATION AND STUDY OF CENTRIFUGAL PUMP COMPUTATION ACCURACY BASED ON MRS AND SMM MODELS.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 112
- By:
- Publication type:
- Article
9
SIMULATION STUDY ON THE VARIATION PATTERN OF TOOL-CHIP CONTACT LENGTH IN THE BTA DEEP-HOLE DRILLING PROCESS.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 104
- By:
- Publication type:
- Article
10
EVALUATION OF BIODEGRADABLE LUBRICANTS BY FORWARD CONICAL CUP -- BACKWARD STRAIGHT CUP EXTRUSION TEST.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 43
- By:
- Publication type:
- Article
11
NOVEL TRENDS IN IMPROVEMENT OF WAREHOUSE MANAGEMENT SYSTEMS FOR MANFACTURING COMPANIES.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 78
- By:
- Publication type:
- Article
12
NON-DESTRUCTIVE TESTING OF RESIDUAL STRESS IN MECHANICAL COMPONENTS BASED ON ULTRASONIC LCR WAVE.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 72
- By:
- Publication type:
- Article
13
APPLICATION OF NEURAL NETWORK TECHNOLOGY IN MACHINING ERROR RECOVERY.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 6
- By:
- Publication type:
- Article
14
MOTION TRAJECTORY PLANNING AND SIMULATION OF 6- DOF MANIPULATOR ARM ROBOT.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 66
- By:
- Publication type:
- Article
15
FIXED CONTROL SYSTEM OF ASSEMBLY ROBOT BASED ON VISION CONTROL.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 60
- By:
- Publication type:
- Article
16
ENERGY SAVING OPTIMIZATION OF MACHINING CENTER PROCESS ROUTE BASED ON IMPROVED GENETIC ALGORITHM.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 35
- By:
- Publication type:
- Article
17
EFFECT OF DIFFERENT MICRO STRUCTURES ON HEAT DISSIPATION OF CPU SURFACE HEAT SINK.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 29
- By:
- Publication type:
- Article
18
Artificial Intelligence and Its Capability.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 5
- By:
- Publication type:
- Article
19
CONSIDERATIONS REGARDING CAM TECHNIQUES FOR ROBOT MILLING.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 23
- By:
- Publication type:
- Article
20
CONTACT RATIO CALCULATION OF INVOLUTE ARC GEAR DEVICE.
- Published in:
- Academic Journal of Manufacturing Engineering, 2017, v. 15, n. 3, p. 19
- By:
- Publication type:
- Article