Works matching IS 14381656 AND DT 2005 AND VI 7 AND IP 8

Results: 14
    1
    2

    Biomorphous SiSiC/Al-Si Ceramic Composites Manufactured by Squeeze Casting: Microstructure and Mechanical PropertiesThe financial support from the German Science Foundation (DFG) and the Volkswagen Foundation is gratefully acknowledged. The TEM-work was carried out at the Laboratory for High-Resolution Electron Microscopy of the University of Erlangen-Nuernberg.

    Published in:
    Advanced Engineering Materials, 2005, v. 7, n. 8, p. 743, doi. 10.1002/adem.200500087
    By:
    • C. Zollfrank;
    • N. Travitzky;
    • H. Sieber;
    • T. Selchert;
    • P. Greil
    Publication type:
    Article
    3
    4

    A Critical Review of the Stress Corrosion Cracking (SCC) of Magnesium AlloysThis research was supported by an Australian Research Council (ARC) Linkage grant in collaboration with General Motors Corporation USA. Atrens and Ghali wish to thank GKSS-Forschungszentrum Geesthacht GmbH for their considerable support that allowed them to work at GKSS as visiting scientists.

    Published in:
    Advanced Engineering Materials, 2005, v. 7, n. 8, p. 659, doi. 10.1002/adem.200500071
    By:
    • N. Winzer;
    • A. Atrens;
    • G. Song;
    • E. Ghali;
    • W. Dietzel;
    • K. U. Kainer;
    • N. Hort;
    • C. Blawert
    Publication type:
    Article
    5
    6
    7
    8

    Quantitative Elastic-Property Measurements at the Nanoscale with Atomic Force Acoustic MicroscopyWe value the contributions to this work made by J. Müller, P. Rice, and J. Wright (NIST). We thank J. Turner (Univ. Nebraska-Lincoln, USA) and W. Arnold, S. Hirsekorn, U. Rabe (IZFP, Germany) for valuable discussions. The nanoindentation measurements were provided by N. Jennett (NPL, UK), A. Rar (Univ. Tennessee-Knoxville, USA), and D. Smith (NIST). We are grateful to G. Pharr (Univ. Tennessee-Knoxville, USA), Y. Dzenis (Univ. Nebraska-Lincoln, USA), P. Dresselhaus, G. Hilton, W. Rippard, and S. Russek (NIST) for providing samples.

    Published in:
    Advanced Engineering Materials, 2005, v. 7, n. 8, p. 713, doi. 10.1002/adem.200500039
    By:
    • D. C. Hurley;
    • M. Kopycinska-Müller;
    • A. B. Kos;
    • R. H. Geiss
    Publication type:
    Article
    9

    Database and Selection Method for Portable Power SourcesThe authors would like to thank Prof. Mike Ashby for his invaluable input and help during various stages of this research. TJL would also like to thank the National Natural Science Foundation of China (Grant No. 10328203) and the National Basic Research Program of China (Grant No. 2006CB601202) for partial financial support.

    Published in:
    Advanced Engineering Materials, 2005, v. 7, n. 8, p. 755, doi. 10.1002/adem.200500037
    By:
    • L. Fu;
    • T. J. Lu;
    • J. E. Huber
    Publication type:
    Article
    10
    11

    Statistical Analysis of Experimental Parameters in Selective Laser SinteringThe fruitful suggestions given by Prof. Paul Darius, Department of Agro-technique and Economics is thankfully acknowledged. One of the authors (S. Kumar) would also like to express his gratitude to Ministry of Human Resources Development, India and Ministry of Flemish Community, Belgium for facilitating his stay in Belgium through Belgium Government Scholarships.

    Published in:
    Advanced Engineering Materials, 2005, v. 7, n. 8, p. 750, doi. 10.1002/adem.200500030
    By:
    • J.-P. Kruth;
    • S. Kumar
    Publication type:
    Article
    12
    13

    Micro-Raman Studies on DLC coatings.

    Published in:
    Advanced Engineering Materials, 2005, v. 7, n. 8, p. 694, doi. 10.1002/adem.200500006
    By:
    • G. Irmer;
    • A. Dorner-Reisel
    Publication type:
    Article
    14