Research on the dynamics of single-acting crank pump with damless hydro turbine drive.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 566, doi. 10.5755/j01.mech.20.6.7432
- By:
- Publication type:
- Article
Works matching IS 13921207 AND DT 2014 AND VI 20 AND IP 6
Results: 12
1
2
Stress intensity for micro-crack emanating from micro-cavity in cement of reconstructed acetabulum.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 527, doi. 10.5755/j01.mech.20.6.9157
- By:
- Publication type:
- Article
3
Automotive stabilizer bar -- stabilizer bar strength calculations using FEM, ovalization of radial areas of tubular stabilizer bars.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 535, doi. 10.5755/j01.mech.20.6.7706
- By:
- Publication type:
- Article
4
Assessment wind field in the region of Annaba East Algeria with an aerodynamic analysis for installation a small wind turbines.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 582, doi. 10.5755/j01.mech.20.6.7504
- By:
- Publication type:
- Article
5
Terms of geometric action of rotating ball follower.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 577, doi. 10.5755/j01.mech.20.6.7419
- By:
- Publication type:
- Article
6
The fiber volume fraction influence on mechanical properties of multi-layered carbon tubes.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 543, doi. 10.5755/j01.mech.20.6.8880
- By:
- Publication type:
- Article
7
Investigation of abrasive water jet cutting parameters influence on 6082 aluminium alloy surface roughness.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 602, doi. 10.5755/j01.mech.20.6.8865
- By:
- Publication type:
- Article
8
Research of rotary piezotable driven by two harmonic signals.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 573, doi. 10.5755/j01.mech.20.6.8797
- By:
- Publication type:
- Article
9
Vibrational excitation of a work piece for drilling force reduction in brittle materials.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 596, doi. 10.5755/j01.mech.20.6.8785
- By:
- Publication type:
- Article
10
Modeling of heat and mass transfer processes in phase transformation cycle of sprayed water into gas: 1. The calculation peculiarities of droplet phase transformation parameters.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 550, doi. 10.5755/j01.mech.20.6.8748
- By:
- Publication type:
- Article
11
Experimental analysis and numerical simulation of the stainless AISI 304 steel friction drilling process.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 590, doi. 10.5755/j01.mech.20.6.8664
- By:
- Publication type:
- Article
12
Classification of vectors forms dedicated to bearings fault detection of electrical machines based on PSO algorithm.
- Published in:
- Mechanika, 2014, v. 20, n. 6, p. 559, doi. 10.5755/j01.mech.20.6.6738
- By:
- Publication type:
- Article