Design optimization of an injection mold for minimizing temperature deviation.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 273, doi. 10.1007/s12239-012-0024-5
- By:
- Publication type:
- Article
Works matching IS 12299138 AND DT 2012 AND VI 13 AND IP 2
Results: 18
1
2
Computational model for analyzing the kinematics and compliance characteristics of a commercial vehicle's front suspension system.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 279, doi. 10.1007/s12239-012-0025-4
- By:
- Publication type:
- Article
3
Non-singular slip (NSS) method for longitudinal tire force calculations in a sudden braking simulation.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 215, doi. 10.1007/s12239-012-0018-3
- By:
- Publication type:
- Article
4
Analytical study of pressure pulsation characteristics according to the geometries of the fuel rail of an MPI engine.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 167, doi. 10.1007/s12239-012-0014-7
- By:
- Publication type:
- Article
5
Development of an electric active rollcontrol (ARC) algorithm for a SUV.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 247, doi. 10.1007/s12239-012-0021-8
- By:
- Publication type:
- Article
6
Optimized energy management control for the Toyota Hybrid System using dynamic programming on a predicted route with short computation time.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 309, doi. 10.1007/s12239-012-0029-0
- By:
- Publication type:
- Article
7
Comparison of the optimum designs of center pillar assembly of an auto-body between conventional steel and ahss with a simplified side impact analysis.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 205, doi. 10.1007/s12239-012-0017-4
- By:
- Publication type:
- Article
8
Design analysis and comparison between standard and rotary porting systems for IC engine.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 175, doi. 10.1007/s12239-012-0015-6
- By:
- Publication type:
- Article
9
Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 285, doi. 10.1007/s12239-012-0026-3
- By:
- Publication type:
- Article
10
A novel adaptive algorithm with an IIR filter and a variable step size for active noise control in a short duct.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 223, doi. 10.1007/s12239-012-0019-2
- By:
- Publication type:
- Article
11
Design of a soft switching bidirectional DC-DC power converter for ultracapacitor-battery interfaces.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 325, doi. 10.1007/s12239-012-0030-7
- By:
- Publication type:
- Article
12
Thin-walled rods with semi-open profile for semi-solid automotive suspension.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 231, doi. 10.1007/s12239-012-0020-9
- By:
- Publication type:
- Article
13
Modeling and analysis of a fuel-injection pump used in diesel engines.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 193, doi. 10.1007/s12239-012-0016-5
- By:
- Publication type:
- Article
14
Numerical modeling of journal bearing considering both elastohydrodynamic lubrication and multi-flexible-body dynamics.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 255, doi. 10.1007/s12239-012-0022-7
- By:
- Publication type:
- Article
15
Cold performance of various biodiesel fuel blends at low temperature.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 293, doi. 10.1007/s12239-012-0027-2
- By:
- Publication type:
- Article
16
Expanding transmission capacity of can systems using dual communication channels with kalman prediction.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 301, doi. 10.1007/s12239-012-0028-1
- By:
- Publication type:
- Article
17
Designing a non-linear tracking controller for vehicle active suspension systems using an optimization process.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 263, doi. 10.1007/s12239-012-0023-6
- By:
- Publication type:
- Article
18
Predicting WCET of automotive software running on virtual machine monitors.
- Published in:
- International Journal of Automotive Technology, 2012, v. 13, n. 2, p. 337, doi. 10.1007/s12239-012-0031-6
- By:
- Publication type:
- Article