Stress Intensity Factors for a Randomly Located Arc-Shaped Crack in a Circular Disk in the Course of Rotation.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 760, doi. 10.1007/s11003-017-0019-5
- By:
- Publication type:
- Article
Works matching IS 1068820X AND DT 2017 AND VI 52 AND IP 6
Results: 17
1
2
Modeling of the Behavior of Plane-Deformable Elastic Media with Elongated Elliptic and Rectangular Inclusions.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 768, doi. 10.1007/s11003-017-0020-z
- By:
- Publication type:
- Article
3
Thermoelasticity of Anisotropic Bimaterial Solids with Contact Thermal Resistance of the Interface Between Their Components and Thin Inclusions.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 775, doi. 10.1007/s11003-017-0021-y
- By:
- Publication type:
- Article
4
Determination of Energy Dissipation in Layered Beams Under Vibratory Loads.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 786, doi. 10.1007/s11003-017-0022-x
- By:
- Publication type:
- Article
5
Evaluation of Stresses in Thin Plates Rigidly Connected with a Cylinder.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 795, doi. 10.1007/s11003-017-0023-9
- By:
- Publication type:
- Article
6
Determination of the Distribution of Hydrogen Near Cracklike Defects.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 803, doi. 10.1007/s11003-017-0024-8
- By:
- Publication type:
- Article
7
Determination of Plane Stress-Strain States of the Plates on the Basis of the Three-Dimensional Theory of Elasticity.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 811, doi. 10.1007/s11003-017-0025-7
- By:
- Publication type:
- Article
8
Friction Sliding of Elastic Bodies in the Presence of Subsurface Inclusions.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 819, doi. 10.1007/s11003-017-0026-6
- By:
- Publication type:
- Article
9
Influence of the Long-Term Operation of Gas Pipelines on the Cyclic Crack-Growth Resistance of 17G1S Steel.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 827, doi. 10.1007/s11003-017-0027-5
- By:
- Publication type:
- Article
10
Surface Hardening of HS6-5-2 Quick-Cutting Steel in the Course of Chemical Thermal Treatment.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 834, doi. 10.1007/s11003-017-0028-4
- By:
- Publication type:
- Article
11
Regularities of Thermal Diffusion Saturation with Nitrogen Combined with Standard Heat Treatment of VT22 Titanium Alloy.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 841, doi. 10.1007/s11003-017-0029-3
- By:
- Publication type:
- Article
12
Serviceability of 60KH2M Roll Steel with Surface Nanostructure.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 848, doi. 10.1007/s11003-017-0030-x
- By:
- Publication type:
- Article
13
Corrosion Resistance of Ribbon and Bulk Amorphous Alloys Based on Iron.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 854, doi. 10.1007/s11003-017-0031-9
- By:
- Publication type:
- Article
14
Corrosion Degradation of Steel of an Elbow of Gas Pipeline with Large-Scale Delamination after Long-Term Operation.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 861, doi. 10.1007/s11003-017-0032-8
- By:
- Publication type:
- Article
15
Invariant Correlation Analysis of the Vibration of Rolling Bearing with Defects on its Outer and Inner Races.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 866, doi. 10.1007/s11003-017-0033-7
- By:
- Publication type:
- Article
16
Acoustic Investigations of the Strained State of Hydrogenated 09G2S Steel.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 875, doi. 10.1007/s11003-017-0034-6
- By:
- Publication type:
- Article
17
New Metal-Hydride Materials Based on RMgNi Alloys for Chemical Current Sources.
- Published in:
- Materials Science, 2017, v. 52, n. 6, p. 747, doi. 10.1007/s11003-017-0018-6
- By:
- Publication type:
- Article