Improving the dynamic precision of the tool position in a machining center.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 77, doi. 10.3103/S1068798X1001017X
- By:
- Publication type:
- Article
Works matching IS 1068798X AND DT 2010 AND VI 30 AND IP 1
Results: 24
1
2
Development of a new theory of thermal cutting processes 1. basic principles.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 64, doi. 10.3103/S1068798X10010144
- By:
- Publication type:
- Article
3
Frictional properties of aluminum bronze facings.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 26, doi. 10.3103/S1068798X10010077
- By:
- Publication type:
- Article
4
Contact-strength estimates of the reliability of conical gears with limited statistical information.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 7, doi. 10.3103/S1068798X10010028
- By:
- Publication type:
- Article
5
Theory of constrained cutting: chip formation with a developed plastic-deformation zone.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 45, doi. 10.3103/S1068798X10010119
- By:
- Publication type:
- Article
6
Precision of duplicate-milling machine with a spherical head.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 102, doi. 10.3103/S1068798X10010247
- By:
- Publication type:
- Article
7
Pass-through lathe cutter with independent cutting systems.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 41, doi. 10.3103/S1068798X10010107
- By:
- Publication type:
- Article
8
Contact stress of connected axisymmetric cylindrical shells of different length in contact-pressure discontinuity zones.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 17, doi. 10.3103/S1068798X10010041
- By:
- Publication type:
- Article
9
Precision basing of blanks with holes on cylindrical and truncated pins.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 51, doi. 10.3103/S1068798X10010120
- By:
- Publication type:
- Article
10
More efficient use of CAE systems in machine tool design.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 67, doi. 10.3103/S1068798X10010156
- By:
- Publication type:
- Article
11
Temperature in contact zone during shot hardening.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 61, doi. 10.3103/S1068798X10010132
- By:
- Publication type:
- Article
12
Finite-element calculation of the dynamic characteristics of the supporting system of a special wheel-boring machine.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 72, doi. 10.3103/S1068798X10010168
- By:
- Publication type:
- Article
13
Machining of housing components in attachments with aerostatic bearings.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 99, doi. 10.3103/S1068798X10010235
- By:
- Publication type:
- Article
14
Efficiency of numerically controlled metal-cutting machines.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 81, doi. 10.3103/S1068798X10010181
- By:
- Publication type:
- Article
15
Influence of the composition of three-element nitride coatings on the state and wear of a cutting tool.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 84, doi. 10.3103/S1068798X10010193
- By:
- Publication type:
- Article
16
Simulating the dynamic reaction of manipulator supports.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 11, doi. 10.3103/S1068798X1001003X
- By:
- Publication type:
- Article
17
Automatic discontinuous 2 transmission lines with sections of different productivity ( q<sub>1</sub> < q<sub>2</sub>).
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 31, doi. 10.3103/S1068798X10010089
- By:
- Publication type:
- Article
18
Fatigue strength of materials in a complex stress state.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 23, doi. 10.3103/S1068798X10010065
- By:
- Publication type:
- Article
19
Influence of contact stress on the life of connected elements.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 1, doi. 10.3103/S1068798X10010016
- By:
- Publication type:
- Article
20
Open optimization in two-dimensional lathe control systems.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 38, doi. 10.3103/S1068798X10010090
- By:
- Publication type:
- Article
21
Edge contact in conical transmissions with round gear teeth.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 20, doi. 10.3103/S1068798X10010053
- By:
- Publication type:
- Article
22
Basing precision of disk and bush blanks in multipoint machining.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 97, doi. 10.3103/S1068798X10010223
- By:
- Publication type:
- Article
23
Influence of the number of segments and their dimensional errors on the primary imbalance vector of a grinding wheel.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 90, doi. 10.3103/S1068798X1001020X
- By:
- Publication type:
- Article
24
Tool management systems.
- Published in:
- Russian Engineering Research, 2010, v. 30, n. 1, p. 94, doi. 10.3103/S1068798X10010211
- By:
- Publication type:
- Article