Investigation on the Clogging Behavior and Additional Wall Cooling for the Axial-Injection Cold Spray Nozzle.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 696, doi. 10.1007/s11666-015-0227-1
- By:
- Publication type:
- Article
Works matching IS 10599630 AND DT 2015 AND VI 24 AND IP 4
Results: 16
1
2
HVO Colloquium 2015: High Velocity Oxy-Fuel Flame Spraying in Focus.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 590, doi. 10.1007/s11666-015-0230-6
- Publication type:
- Article
3
Tribological Behavior of Ferrous-Based APS Coatings Under Dry Sliding Conditions.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 671, doi. 10.1007/s11666-014-0202-2
- By:
- Publication type:
- Article
4
Optimization of High Porosity Thermal Barrier Coatings Generated with a Porosity Former.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 622, doi. 10.1007/s11666-014-0214-y
- By:
- Publication type:
- Article
5
Simulation of Motion, Heating, and Breakup of Molten Metal Droplets in the Plasma Jet at Plasma-Arc Spraying.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 659, doi. 10.1007/s11666-015-0216-4
- By:
- Publication type:
- Article
6
Measurement of the Average Two-Dimensional Surface Temperature Distribution of Drops in a Melt Atomization Process.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 690, doi. 10.1007/s11666-015-0217-3
- By:
- Publication type:
- Article
7
Healing of the Interface Between Splashed Particles and Underlying Bulk Coating and Its Influence on Isothermal Oxidation Behavior of LPPS MCrAlY Bond Coat.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 611, doi. 10.1007/s11666-015-0218-2
- By:
- Publication type:
- Article
8
Ta and Ti Anti-passivation Interlayers for Oxygen-Evolving Anodes Produced by Cold Gas Spray.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 702, doi. 10.1007/s11666-015-0219-1
- By:
- Publication type:
- Article
9
Acoustic Measurements in a Hexamethyldisiloxane-Loaded Low-Temperature Direct Barrier Discharge (DBD) Plasma Effluent: Nozzle Cleaning.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 683, doi. 10.1007/s11666-015-0220-8
- By:
- Publication type:
- Article
10
Microstructure of Kinetic Spray Coatings: A Review.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 592, doi. 10.1007/s11666-015-0223-5
- By:
- Publication type:
- Article
11
Mitigating Localized Corrosion Using Thermally Sprayed Aluminum (TSA) Coatings on Welded 25% Cr Superduplex Stainless Steel.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 629, doi. 10.1007/s11666-015-0224-4
- By:
- Publication type:
- Article
12
Post-treatment of Plasma-Sprayed Amorphous Ceramic Coatings by Spark Plasma Sintering.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 637, doi. 10.1007/s11666-015-0225-3
- By:
- Publication type:
- Article
13
Ceramic Nano-particle/Substrate Interface Bonding Formation Derived from Dynamic Mechanical Force at Room Temperature: HRTEM Examination.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 720, doi. 10.1007/s11666-015-0226-2
- By:
- Publication type:
- Article
14
The Effects of Contact Conditions on the Onset of Shear Instability in Cold-Spray.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 711, doi. 10.1007/s11666-015-0229-z
- By:
- Publication type:
- Article
15
Thanks to Our Guest Editors and Reviewers for Their Critical Contributions in 2014.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 587, doi. 10.1007/s11666-015-0233-3
- Publication type:
- Article
16
Single Impact Bonding of Cold Sprayed Ti-6Al-4V Powders on Different Substrates.
- Published in:
- Journal of Thermal Spray Technology, 2015, v. 24, n. 4, p. 644, doi. 10.1007/s11666-014-0200-4
- By:
- Publication type:
- Article