圆锥滚子球基面磨削力模型及实验研究.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 679, doi. 10.3969/j.issn.1004-132X.2020.06.007
- By:
- Publication type:
- Article
Works matching IS 1004132X AND DT 2020 AND VI 31 AND IP 6
Results: 15
1
2
两挡纯电动汽车多目标参数解耦优化方法.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 746, doi. 10.3969/j.issn.1004-132X.2020.06.015
- By:
- Publication type:
- Article
3
考虑修正平均等效应力强度因子的焊点 缺陷疲劳寿命研究.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 740, doi. 10.3969/j.issn.1004-132X.2020.06.014
- By:
- Publication type:
- Article
4
基于自适应拓扑的电池动态分组均衡方法.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 714, doi. 10.3969/j.issn.1004-132X.2020.06.011
- By:
- Publication type:
- Article
5
云制造供应链知识转移激励的演化博弈模型.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 695, doi. 10.3969/j.issn.1004-132X.2020.06.009
- By:
- Publication type:
- Article
6
基于混合离散蝙幅算法的跨工序协同调度问题.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 731, doi. 10.3969/j.issn.1004-132X.2020.06.013
- By:
- Publication type:
- Article
7
一种基于手眼视觉的并联机器人标定方法.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 722, doi. 10.3969/j.issn.1004-132X.2020.06.012
- By:
- Publication type:
- Article
8
2-RPaRSS并联操作手运动副间隙误差分析及补偿.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 706, doi. 10.3969/j.issn.1004-132X.2020.06.010
- By:
- Publication type:
- Article
9
超声振动光整的EDEM数值模拟与实验研究.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 647, doi. 10.3969/j.issn.1004-132X.2020.06.003
- By:
- Publication type:
- Article
10
轴铆自转速度和进给速度对轮毂轴承性能的影响.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 688, doi. 10.3969/j.issn.1004-132X.2020.06.008
- By:
- Publication type:
- Article
11
无刷直流电机两管导通零矢量直接转矩控制.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 670, doi. 10.3969/j.issn.1004-132X.2020.06.006
- By:
- Publication type:
- Article
12
光催化条件下钴基合金材料去除方法.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 662, doi. 10.3969/j.issn.1004-132X.2020.06.005
- By:
- Publication type:
- Article
13
切削参数对剃齿切削力及齿形中凹误差的影响.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 655, doi. 10.3969/j.issn.1004-132X.2020.06.004
- By:
- Publication type:
- Article
14
超高压大流量比例插装阀测试方法.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 638, doi. 10.3969/j.issn.1004-132X.2020.06.002
- By:
- Publication type:
- Article
15
基于行驶工况的插电式混合动力公交车 控制参数自动化标定方法.
- Published in:
- China Mechanical Engineering, 2020, v. 31, n. 6, p. 631, doi. 10.3969/j.issn.1004-132X.2020.06.001
- By:
- Publication type:
- Article