Works matching IS 08981507 AND DT 2022 AND VI 52 AND IP 4-6

Results: 12

Analysis of Powder Feeding Behaviour in Coaxial Laser Cladding.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 361
By:
- CUI, Y. H.;
- WU, L. L.;
- YANG, Y. C.;
- LAN, Y. C.;
- LIN, J. L.;
- FANG, N. W.;
- CHEN, X. Y.;
- LI, R.
Publication type:
Article
Parameter Optimization for Laser Ring Welding Dissimilar Steel Piston Rods.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 341
By:
- YA, F-P.;
- LI, J-H.;
- LIU, T-Y.
Publication type:
Article
Describing the Influence of Laser Cutting Parameters on a SiC Reinforced Al Alloy Metal Matrix Composite (MMC) Using Response Surface Methodology (RSM).
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 319
By:
- SHAJAHAN, C. M.;
- LALHMINGSANGA, H.;
- KURIACHEN, B.
Publication type:
Article
Investigation of Six Contamination Parameters Via a Two-dimensional (2-D) Photonic Structure (PhC) Using an Infrared (IR) Laser Beam.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 309
By:
- KUMAR, B. A.;
- SAHU, S. K.;
- PALAI, G.
Publication type:
Article
Research State-of-the-Art on Controlling Ti-Al Intermetallic Compound (IMC) Formation During the Laser Beam Welding (LBW) of Ti and Al Alloys.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 299
By:
- YU, D-S.;
- ZHOU, J-P.;
- ZHANG, Y.
Publication type:
Article
Deformation Behaviour of Open-cell AlSi10Mg Alloy Formed By Selective Laser Melting (SLM).
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 283
By:
- BAI, P-K.;
- YANG, X.;
- WANG, J.;
- DU, W-B.;
- ZHAO, Z-Y.;
- Wang, W-X.
Publication type:
Article
Morphology Control and Process Optimization for the Laser Cladding of Ni60 Alloy onto H13 Steel.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 261
By:
- LI, J-H.;
- XUE, S-L.;
- YAO, F-P.;
- AN, X-J.;
- JIN, J-B.
Publication type:
Article
Fingertip Touch-based Non-invasive Glucose Sensor Using Visible Laser Light in a SiO<sub>2</sub>-Au-SiO<sub>2</sub> Coated Prism: Design and Implementation Using the Matrix Method.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 247
By:
- DASH, S. P.;
- HOTA, M.;
- TRIAPTHY, S. K.
Publication type:
Article
Fabrication of Crack-free Glass Microfluidic Chips with Tape-assisted Laser Engraving.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 187
By:
- SUN, L-L.;
- YANG, X.;
- DING, A.;
- ZHANG, B-Y.;
- YIN, Z-F.
Publication type:
Article
Laser and Laser-Liquid Composite Etching of Si Wafers.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 233
By:
- LI, X.;
- CHEN, Y-L.;
- SI, X-D.;
- LI, H-G.;
- CHEN, X-H.
Publication type:
Article
Effect of Nb Content on the Microstructure and Mechanical Properties of a Stellite 20 Laser Clad onto Cast Steel.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 217
By:
- GU, X-Y.;
- GONG, H. T.;
- SONG, Y-J.;
- GU, X-P.;
- LI, H-M.;
- ZHAO, X-H.;
- LIU, L.
Publication type:
Article
A Novel Radio Frequency Identification (RFID) Dynamic Performance Measurement System Based on Laser Ranging and Humidity Control.
Published in:
Lasers in Engineering (Old City Publishing), 2022, v. 52, n. 4-6, p. 201
By:
- LIU, Z-L.;
- YU, X-L.;
- ZHU, Z.;
- ZHUANG, X.;
- LI, L.;
- ZHAO, Z-M.
Publication type:
Article