A Three-dimensional (3-D) Reconstruction Approach Using Single Layer Lidar and an Inertial Measurement Unit.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 187
- By:
- Publication type:
- Article
Works matching IS 08981507 AND DT 2019 AND VI 42 AND IP 1-3
Results: 12
1
2
High Speed Laser Butt Welding of Cr-Plated Stainless Steel Sheets.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 177
- By:
- Publication type:
- Article
3
Influence of Carbon and RE Oxides on the Crystal Morphologies in Laser Fabricated Composites.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 169
- By:
- Publication type:
- Article
4
Laser Short Pulse Heating of an Aluminium Film: Thermal Analysis Incorporating the Equation for Phonon Radiative Transport.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 57
- By:
- Publication type:
- Article
5
Influence of Rescanning Process on Thermo-mechanical Response of Molten Zone in Laser Cladding on Gray Cast Iron.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 129
- By:
- Publication type:
- Article
6
Optimization for Calibration Model of Workspace Measurement Positioning System (wMPS) Based on Distance Constraint.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 113
- By:
- Publication type:
- Article
7
Microstructural and Mechanical Characterization of a Fibre Laser Welded T-joint in High Strength Steel.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 99
- By:
- Publication type:
- Article
8
Microstructure and Properties of TiN/AlN Multilayer Thin Films Prepared by Pulsed Laser Deposition (PLD).
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 83
- By:
- Publication type:
- Article
9
Parameterization and Process Influence of Graphite Morphology in the Laser Cladding of Grey Cast Iron.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 151
- By:
- Publication type:
- Article
10
An Automatic Determination for Planar Target Points via C-Means Approach in the Terrestrial Laser Scanning Data.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 31
- By:
- Publication type:
- Article
11
Characterization of a Yb:YAG Disk Laser Line Welder for Ultra-thin Steel Strip in Industrial Cold-Rolling Mill.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 15
- By:
- Publication type:
- Article
12
FeCrNiMnMo<sub>x</sub>Si<sub>0.5</sub>B<sub>0.5</sub> High-entropy Alloy (HEA) Coatings Fabricated by Laser Cladding.
- Published in:
- Lasers in Engineering (Old City Publishing), 2019, v. 42, n. 1-3, p. 1
- By:
- Publication type:
- Article