Works matching IS 03548996 AND DT 2022 AND VI 44 AND IP 2
Results: 14
A Method to Evaluate Wear and Vibration Characteristics of CNC Lathe Spindle.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 352, doi. 10.24874/ti.1206.10.21.04
- By:
- Publication type:
- Article
Influence of the Structural State of the Mg-1%Ca Magnesium Alloy on Tribological Properties.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 343, doi. 10.24874/ti.1162.08.21.02
- By:
- Publication type:
- Article
A Study on the Relationship Between Contact Pressures in a Grade2 TDN--UHMWPE Hip Implant: Young's Modulus and Poisson's Ratio.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 334, doi. 10.24874/ti.1233.12.21.03
- By:
- Publication type:
- Article
Computer Simulation and Optimization of Elliptic Bore Journal Bearing.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 322, doi. 10.24874/ti.1179.09.21.01
- By:
- Publication type:
- Article
Influence of Heat Treatment of 30MnB5 Steel on its Micromechanical Properties and Resistance to Abrasion Wear.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 310, doi. 10.24874/ti.1146.06.21.02
- By:
- Publication type:
- Article
Investigation on the Mechanical and Wear Behaviour of Al-6082-BN-B<sub>4</sub>C-Corn Cob Ash Hybrid Composites.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 294, doi. 10.24874/ti.1165.08.21.11
- By:
- Publication type:
- Article
Microstructure and Wear Resistance of Plasma Surface Layers Based of Alloy Mixture CuSn10/CrxCy.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 212, doi. 10.24874/ti.1083.03.21.07
- By:
- Publication type:
- Article
Comparative Investigations on Microstructure and Slurry Abrasive Wear Resistance of NiCrBSi and NiCrBSi-WC Composite Hardfacings Deposited on 304 Stainless Steel.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 199, doi. 10.24874/ti.1075.03.21.05
- By:
- Publication type:
- Article
Experimental and Statistical Study of Surface Roughness in CNC Slot Milling of AL 7075 Alloy Using Full and Fractional Factorial Design.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 283, doi. 10.24874/ti.1151.07.21.11
- By:
- Publication type:
- Article
Friction Coefficient of Rubber Shoe Sole Sliding Against Different Rubber Floor Tiles.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 244, doi. 10.24874/ti.1188.09.21.11
- By:
- Publication type:
- Article
Microstructural Characterization, Residual Stress, and Mechanical Properties of Plasma Sprayed 8YSZ Thermal Barrier Coatings.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 230, doi. 10.24874/ti.1105.05.21.07
- By:
- Publication type:
- Article
Optimization of Plasma Spraying Parameters with Respect to Shear Adhesion Strength of Cr3C2-NiCr Coating on 16Mn Steel.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 221, doi. 10.24874/ti.1101.04.21.09
- By:
- Publication type:
- Article
Analysis of Oil Distribution and Reduction of Axial Force due to Oil Supply in a Multi-Plate Clutch.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 268, doi. 10.24874/ti.1168.08.21.11
- By:
- Publication type:
- Article
Optimization of Abrasive Wear Parameters of Halloysite Nanotubes Reinforced Silk/Basalt Hybrid Epoxy Composites using Taguchi Approach.
- Published in:
- Tribology in Industry, 2022, v. 44, n. 2, p. 253, doi. 10.24874/ti.1131.06.21.08
- By:
- Publication type:
- Article