Efficiency Analysis of New Two-Stage Cycloid Drive Concept.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 337, doi. 10.24874/ti.880.05.20.06
- By:
- Publication type:
- Article
Works matching IS 03548996 AND DT 2020 AND VI 42 AND IP 2
Results: 15
1
2
Characterization and Wear Behaviour of WC-Co Coated Copper under Dry Sliding Conditions.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 327, doi. 10.24874/ti.771.09.19.03
- By:
- Publication type:
- Article
3
Influence of Tool Tip Temperature on Crater Wear of Ceramic Inserts During Turning Process of Inconel-718 at Varying Hardness.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 310, doi. 10.24874/ti.776.10.19.05
- By:
- Publication type:
- Article
4
Determining the Significance of Cobalt Addition on the Wear Characteristics of Al-6.6Si-0.4Mg Hypoeutectic Alloy Using Design of Experiment.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 299, doi. 10.24874/ti.777.10.19.04
- By:
- Publication type:
- Article
5
Investigation of the Penetration and Temperature of the Friction Pair Under Different Working Conditions.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 288, doi. 10.24874/ti.849.02.20.05
- By:
- Publication type:
- Article
6
The Tribological Performance of Hydrodynamic Journal Bearing Using Bio-based Lubricant.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 278, doi. 10.24874/ti.843.02.20.05
- By:
- Publication type:
- Article
7
Wear and Friction Study of Centrifugally Cast Functionally Graded Cu-Ni-Si Alloy and Composite.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 267, doi. 10.24874/ti.754.08.19.03
- By:
- Publication type:
- Article
8
The Tribological, Physico-Chemical and Rheological Properties of Lubricating Grease Produced on Epoxy Resin Base.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 255, doi. 10.24874/ti.760.09.19.04
- By:
- Publication type:
- Article
9
Influence of Operating Parameters on Slurry Erosion of Stainless Steel F6NM.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 236, doi. 10.24874/ti.780.10.19.02
- By:
- Publication type:
- Article
10
Effect of Laser Energy on the Tribology Properties of MoS<sub>2</sub> Flakes.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 225, doi. 10.24874/ti.787.11.19.02
- By:
- Publication type:
- Article
11
Inhibitive Action of Glutathione Reduced on the Deterioration of AA6061 in 0.5M HCl.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 214, doi. 10.24874/ti.785.10.19.02
- By:
- Publication type:
- Article
12
Tribological Properties of Coatings Obtained with Electrocontact Welding of Metal Powder Materials.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 200, doi. 10.24874/ti.655.02.19.03
- By:
- Publication type:
- Article
13
Tribological Properties of Coatings Obtained with Electrocontact Welding of Metal Powder Materials.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 191, doi. 10.24874/ti.828.01.20.03
- By:
- Publication type:
- Article
14
Tribological Performance of Brass Powder with Different Copper and Zinc Content in the Brake pad.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 177, doi. 10.24874/ti.783.10.19.03
- By:
- Publication type:
- Article
15
Effect of Abrasive Soil Mass Grain Size on the Steel Wear Process.
- Published in:
- Tribology in Industry, 2020, v. 42, n. 2, p. 165, doi. 10.24874/ti.784.10.19.04
- By:
- Publication type:
- Article