Works matching IS 03548996 AND DT 2015 AND VI 37 AND IP 2
Results: 15
Influence of the Lubricant Type on the Surface Quality of Steel Parts Obtained by Ironing.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 215
- By:
- Publication type:
- Article
Softening Resistance, Dimensional Stability and Corrosion Behaviour of Alumina and Rice Husk Ash Reinforced Aluminium Matrix Composites Subjected to Thermal Cycling.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 204
- By:
- Publication type:
- Article
Wear and Friction Behavior of in-situ AA5052/ZrB<sub>2</sub>Composites under Dry Sliding Conditions.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 244
- By:
- Publication type:
- Article
Multi-Criteria Analysis of Laser Cut Surface Characteristics in CO<sub>2</sub> Laser Cutting of Stainless Steel.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 236
- By:
- Publication type:
- Article
Modeling and Development of RMD Configuration Magnetic Bearing.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 225
- By:
- Publication type:
- Article
Study of Effect of Seal Profile on Tribological Characteristics of Reciprocating Hydraulic Seals.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 264
- By:
- Publication type:
- Article
Synthesis of Uncarbonised Coconut Shell Nanoparticles: Characterisation and Particle Size Determination.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 257
- By:
- Publication type:
- Article
Analysis of Anti-Wear Properties of CuO Nanoparticles as Friction Modifiers in Mineral Oil (460cSt Viscosity) Using Pin-On-Disk Tribometer.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 196
- By:
- Publication type:
- Article
Improve Simulation of Plain Bearings in Dry and Mixed Lubrication Regime by Defining Locally Resolved Dry Friction Coefficients.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 186
- By:
- Publication type:
- Article
A Comparative Experimental Study on Identification of Defect Severity in Rolling Element Bearings using Acoustic Emission and Vibration Analysis.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 176
- By:
- Publication type:
- Article
Slew Bearings Damage Detection using Hilbert Huang Transformation and Acoustic Methods.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 170
- By:
- Publication type:
- Article
Effects of Surface Roughness in Squeeze Film Lubrication of Two Parallel Plates.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 161
- By:
- Publication type:
- Article
Tribological Properties of Silicone Rubber-Based Ceramizable Composites Destined for Wire Covers. Part I. Studies of Block-On-Ring Friction Contact.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 154
- By:
- Publication type:
- Article
Suitability of Recycled Polyethylene/Palm Kernel Shell-Iron Filings Composite for Automobile Application.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 142
- By:
- Publication type:
- Article
Jenkins Model Based Ferrofluid Lubrication of a Curved Rough Annular Squeeze Film with Slip Velocity.
- Published in:
- Tribology in Industry, 2015, v. 37, n. 2, p. 129
- By:
- Publication type:
- Article