Creep and relaxation behavior of woven glass/epoxy substrates for multilayer circuit board applications.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 567, doi. 10.1002/pc.10130
- By:
- Publication type:
- Article
Works matching IS 02728397 AND DT 1998 AND VI 19 AND IP 5
Results: 14
1
2
An interface model for the prediction of Young's modulus of layered silicate-elastomer nanocomposites.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 608, doi. 10.1002/pc.10134
- By:
- Publication type:
- Article
3
Flow channels/fiber impregnation studies for the process modeling/analysis of complex engineering structures manufactured by resin transfer molding.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 527, doi. 10.1002/pc.10127
- By:
- Publication type:
- Article
4
Impact behavior of carbon fiber/polyethylene fiber hybrid composite: The effect of surface treatment of polyethylene fiber.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 600, doi. 10.1002/pc.10133
- By:
- Publication type:
- Article
5
Sliding mode interlaminar fracture toughness of interply hybrid composite materials.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 514, doi. 10.1002/pc.10126
- By:
- Publication type:
- Article
6
On the effect of the fiber orientation on the flexural stiffness of injection molded short fiber reinforced polycarbonate plates.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 640, doi. 10.1002/pc.10137
- By:
- Publication type:
- Article
7
Anisotropic modeling of isothermal squeezing flow of Glass-Mat reinforced thermoplastics (GMT).
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 588, doi. 10.1002/pc.10132
- By:
- Publication type:
- Article
8
A generalized self-consistent mori-tanaka scheme for prediction of the effective elastic moduli of hybrid multiphase particulate composites.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 506, doi. 10.1002/pc.10125
- By:
- Publication type:
- Article
9
Effect of fiber architecture on permeability in liquid composite molding.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 626, doi. 10.1002/pc.10136
- By:
- Publication type:
- Article
10
Power issues in the manufacturing and characterization of polymers and composite materials.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 558, doi. 10.1002/pc.10129
- By:
- Publication type:
- Article
11
Polymerization of styrene-isoprene on glass cloth for use in composite manufacture.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 579, doi. 10.1002/pc.10131
- By:
- Publication type:
- Article
12
Practical use of the statistically modified laminate model for injection moldings. Part 1: Method and verification.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 497, doi. 10.1002/pc.10124
- By:
- Publication type:
- Article
13
Effect of carbon fabric type on the mechanical performance of 2D carbon/carbon composites.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 618, doi. 10.1002/pc.10135
- By:
- Publication type:
- Article
14
Compaction of textile reinforcements for composites manufacturing. II: Compaction and relaxation of dry and H<sub>2</sub>O-saturated woven reinforcements.
- Published in:
- Polymer Composites, 1998, v. 19, n. 5, p. 543, doi. 10.1002/pc.10128
- By:
- Publication type:
- Article