Construct MIMO process control system by using soft computing methods.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 511, doi. 10.1007/s00170-006-0464-z
- By:
- Publication type:
- Article
Works matching IS 02683768 AND DT 2007 AND VI 33 AND IP 5/6
Results: 22
1
2
A component-based product data management system.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 614, doi. 10.1007/s00170-006-0482-x
- By:
- Publication type:
- Article
3
A note on single-machine scheduling with learning effect and an availability constraint.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 540, doi. 10.1007/s00170-006-0469-7
- By:
- Publication type:
- Article
4
Robust control of a 3-DOF hybrid robot manipulator.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 604, doi. 10.1007/s00170-006-0474-x
- By:
- Publication type:
- Article
5
Optimized sequential design of two-dimensional tolerances.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 579, doi. 10.1007/s00170-006-0475-9
- By:
- Publication type:
- Article
6
An integrated manufacturing information system for mass sheet metal cutting.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 436, doi. 10.1007/s00170-006-0484-8
- By:
- Publication type:
- Article
7
Optimization of contact forces in tailor-welded blanks forming process.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 460, doi. 10.1007/s00170-006-0491-9
- By:
- Publication type:
- Article
8
Influence of process parameters on part shrinkage in SLS.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 498, doi. 10.1007/s00170-006-0490-x
- By:
- Publication type:
- Article
9
Applying grey forecasting method for fitting and predicting the performance characteristics of an electro-conductive ceramic (Al<sub>2</sub>O<sub>3</sub>+30%TiC) during electrical discharge machining.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 480, doi. 10.1007/s00170-006-0488-4
- By:
- Publication type:
- Article
10
Parameter optimization of non-vertical laser cutting.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 469, doi. 10.1007/s00170-006-0489-3
- By:
- Publication type:
- Article
11
Grinding force and power modeling based on chip thickness analysis.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 449, doi. 10.1007/s00170-006-0473-y
- By:
- Publication type:
- Article
12
GA-based synthesis approach for machining scheme selection and operation sequencing optimization for prismatic parts.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 594, doi. 10.1007/s00170-006-0477-7
- By:
- Publication type:
- Article
13
Effects of finishing in abrasive fluid machining on microholes fabricated by EDM.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 489, doi. 10.1007/s00170-006-0485-7
- By:
- Publication type:
- Article
14
Dual commands dispatching of a class-based unit-load automated storage and retrieval system using multi-pass simulation with generic algorithm.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 530, doi. 10.1007/s00170-006-0478-6
- By:
- Publication type:
- Article
15
Design of integrated manufacturing planning, scheduling and control systems: a new framework for automation.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 545, doi. 10.1007/s00170-006-0476-8
- By:
- Publication type:
- Article
16
Reverse engineering: a selective sampling acquisition approach.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 521, doi. 10.1007/s00170-006-0472-z
- By:
- Publication type:
- Article
17
Establishment of a cutting force model and study of the stress–strain distribution in nano-scale copper material orthogonal cutting.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 425, doi. 10.1007/s00170-006-0480-z
- By:
- Publication type:
- Article
18
Basic study on pulse generator for micro-EDM.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 474, doi. 10.1007/s00170-006-0483-9
- By:
- Publication type:
- Article
19
A new algorithm for determining production schedules when solving the multi-product economic lot sizing problem in flow shops.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 560, doi. 10.1007/s00170-006-0479-5
- By:
- Publication type:
- Article
20
The evaluation of process capability for a machining center.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 505, doi. 10.1007/s00170-006-0481-y
- By:
- Publication type:
- Article
21
Boolean operations of STL models based on loop detection.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 33, n. 5/6, p. 627, doi. 10.1007/s00170-006-0487-5
- By:
- Publication type:
- Article
22
Boolean operations of STL models based on loop detection.
- Published in:
- 2007
- By:
- Publication type:
- Correction Notice