Works matching IS 02683768 AND DT 2007 AND VI 31 AND IP 9/10
Results: 23
Infrastructure for co-ordination of multi-agents in a network–based manufacturing system.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 1028, doi. 10.1007/s00170-005-0115-9
- By:
- Publication type:
- Article
Coordinating supply chain response-time: a bi-level programming approach.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 1034, doi. 10.1007/s00170-005-0260-1
- By:
- Publication type:
- Article
An effective hybrid particle swarm optimization for no-wait flow shop scheduling.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 1001, doi. 10.1007/s00170-005-0277-5
- By:
- Publication type:
- Article
Influence of material flow constraints during cold forming on the deformation and densification behaviour of hypoeutectoid P/M steel ring preforms.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 926, doi. 10.1007/s00170-005-0272-x
- By:
- Publication type:
- Article
A design advisor for the optimal inspection of circularity tolerance.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 857, doi. 10.1007/s00170-005-0273-9
- By:
- Publication type:
- Article
FIPA agent-based control system design for FMS.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 969, doi. 10.1007/s00170-005-0281-9
- By:
- Publication type:
- Article
A successive approximation algorithm for the inverse position analysis of the general serial manipulators.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 1021, doi. 10.1007/s00170-005-0271-y
- By:
- Publication type:
- Article
An intelligent process planning system for prismatic parts using STEP features.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 978, doi. 10.1007/s00170-005-0269-5
- By:
- Publication type:
- Article
Surface error decomposition for fixture development.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 948, doi. 10.1007/s00170-005-0270-z
- By:
- Publication type:
- Article
A novel arc-spraying robot for rapid tooling.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 1012, doi. 10.1007/s00170-005-0264-x
- By:
- Publication type:
- Article
Analysis and prediction of cutting forces in end milling by means of a geometrical model.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 888, doi. 10.1007/s00170-005-0275-7
- By:
- Publication type:
- Article
Development of a high–resolution rapid prototyping system for small size objects.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 941, doi. 10.1007/s00170-005-0257-9
- By:
- Publication type:
- Article
Analysis and simulation for a parallel drill point grinder.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 915, doi. 10.1007/s00170-005-0265-9
- By:
- Publication type:
- Article
Review of dynamic issues in micro-end-milling.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 897, doi. 10.1007/s00170-005-0276-6
- By:
- Publication type:
- Article
A comparison of two methods for transforming non-normal manufacturing data.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 957, doi. 10.1007/s00170-005-0279-3
- By:
- Publication type:
- Article
The development of an in-process surface roughness adaptive control system in end milling operations.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 877, doi. 10.1007/s00170-005-0262-z
- By:
- Publication type:
- Article
Investigation of dry machining with embedded heat pipe cooling by finite element analysis and experiments.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 905, doi. 10.1007/s00170-005-0266-8
- By:
- Publication type:
- Article
A finite element-based model for pure waterjet process simulation.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 933, doi. 10.1007/s00170-005-0274-8
- By:
- Publication type:
- Article
A technique for advanced manufacturing systems capability evaluation and comparison (ACEC).
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 1044, doi. 10.1007/s00170-005-0268-6
- By:
- Publication type:
- Article
A mixed isomorphism approach for kinematic structure enumeration graphs based on intelligent design and manufacturing.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 841, doi. 10.1007/s00170-005-0263-y
- By:
- Publication type:
- Article
Virtual engineering approaches in product and process design.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 846, doi. 10.1007/s00170-005-0267-7
- By:
- Publication type:
- Article
Application of particle swarm optimisation in artificial neural network for the prediction of tool life.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 871, doi. 10.1007/s00170-005-0252-1
- By:
- Publication type:
- Article
A genetic algorithm for solving the single machine earliness/tardiness problem with distinct due dates and ready times.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 31, n. 9/10, p. 994, doi. 10.1007/s00170-005-0261-0
- By:
- Publication type:
- Article