Pycnometric Determination of Porosity Characteristics.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 420, doi. 10.1134/S0020168524700651
- By:
- Publication type:
- Article
Works matching IS 00201685 AND DT 2024 AND VI 60 AND IP 4
Results: 24
1
2
Evaluation of Error in Residual Stress Measurements by the Hole Drilling Method.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 553, doi. 10.1134/S0020168524700614
- By:
- Publication type:
- Article
3
Low-Cycle Fracture Resistance of the Superalloy at Single- and Two-Frequency Modes of Loading.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 547, doi. 10.1134/S0020168524700602
- By:
- Publication type:
- Article
4
Root Cause Analysis of the Brittle Fracture of Pipes of Boiler Heating Surfaces after Long-Term Operation.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 516, doi. 10.1134/S0020168524700559
- By:
- Publication type:
- Article
5
Fields of Residual Stresses near Filled Assemblage Holes of the Aircraft Wing Panel.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 560, doi. 10.1134/S0020168524700626
- By:
- Publication type:
- Article
6
Fatigue Fracture of 316L Steel Manufactured by Selective Laser Melting.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 536, doi. 10.1134/S0020168524700596
- By:
- Publication type:
- Article
7
Application of the Magnetic Method for Control of the Deformed State of Samples Made of ER308LSI Steel Produced by Additive Growing.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 528, doi. 10.1134/S0020168524700560
- By:
- Publication type:
- Article
8
A Study of the Effect of the Macrogeometry of Rubbing Steel Bodies upon Their Point Contact on the Tribological Characteristics of Lubricants under Boundary Lubrication Conditions.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 510, doi. 10.1134/S0020168524700547
- By:
- Publication type:
- Article
9
Structure and Properties of Ti<sub>x</sub>Mo<sub>1–x</sub>C<sub>y</sub>N<sub>z</sub> Interstitial Alloys.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 425, doi. 10.1134/S0020168524700663
- By:
- Publication type:
- Article
10
Analysis of the Effect of the Direction of Reinforcement of a Fibrous Composite Material on the Inhomogeneity of Localization of Deformations and Stresses Using the Method of Thermoelastic Response.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 502, doi. 10.1134/S0020168524700535
- By:
- Publication type:
- Article
11
Installation and Testing Methods for Frequency Stability under Cyclic Loading of Metals and Alloys.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 494, doi. 10.1134/S0020168524700523
- By:
- Publication type:
- Article
12
Application of Numerical Differentiation Methods to Determination of the Fatigue Crack Growth Rate.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 486, doi. 10.1134/S0020168524700511
- By:
- Publication type:
- Article
13
Equation of State for Viscoelasticity of Polymethyl Methacrylate.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 476, doi. 10.1134/S002016852470050X
- By:
- Publication type:
- Article
14
Potentiality of the Probabilistic Risk Analysis of Damaged Technical Objects Using the Gamma Model.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 469, doi. 10.1134/S0020168524700493
- By:
- Publication type:
- Article
15
Study of the Stages of Cavitation Development in Channels Based on Hydro- and Sonoluminescence Measurements.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 464, doi. 10.1134/S0020168524700729
- By:
- Publication type:
- Article
16
Study of the Structure of Filler Composite Wire for Surfacing Wear-Resistant Layers.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 456, doi. 10.1134/S0020168524700717
- By:
- Publication type:
- Article
17
Study of Dielectric Properties of Decomposing Materials during Heating.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 450, doi. 10.1134/S0020168524700705
- By:
- Publication type:
- Article
18
High-Voltage Power Supply for X-ray Control of the Structure of Materials.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 444, doi. 10.1134/S0020168524700699
- By:
- Publication type:
- Article
19
Research of Sediments in Assessing the Causes of Corrosion at Gas Facilities.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 437, doi. 10.1134/S0020168524700687
- By:
- Publication type:
- Article
20
Study of Mechanical Properties and Microstructure of Welded Joints Made of Structural High-Strength Steel S690QL of Russian and Foreign Production.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 431, doi. 10.1134/S0020168524700675
- By:
- Publication type:
- Article
21
Modeling of the Thermophysical Properties of Molding Materials by Solving the Inverse Heat Conduction Problem.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 413, doi. 10.1134/S002016852470064X
- By:
- Publication type:
- Article
22
Descent along Nodal Straight Lines and Simplex Algorithm: Two Options of Regression Analysis Based on the Least Absolute Deviations Method.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 397, doi. 10.1134/S0020168524700584
- By:
- Publication type:
- Article
23
Evaluation of the Use of Polyvinyl Alcohol in Preparation of Pressed Samples for X-ray Fluorescence Analysis.
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 405, doi. 10.1134/S0020168524700638
- By:
- Publication type:
- Article
24
Methodological Issues of the Fuzzy Set Theory (Generalizing Article).
- Published in:
- Inorganic Materials, 2024, v. 60, n. 4, p. 389, doi. 10.1134/S0020168524700572
- By:
- Publication type:
- Article