Mechanics of Additively Manufactured Materials.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 791, doi. 10.1007/s11340-019-00537-9
- Publication type:
- Article
Works matching IS 00144851 AND DT 2019 AND VI 59 AND IP 6
Results: 12
1
2
In-Situ Visualization of Tensile Failure in Additively Manufactured 316 L Stainless Steel.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 805, doi. 10.1007/s11340-019-00524-0
- By:
- Publication type:
- Article
3
Mechanical Properties of Printed Epoxy-Carbon Fiber Composites.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 843, doi. 10.1007/s11340-019-00498-z
- By:
- Publication type:
- Article
4
Mechanical Properties of Selective Laser Sintering (SLS) Additive Manufactured Chiral Auxetic Cylindrical Stent.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 913, doi. 10.1007/s11340-019-00489-0
- By:
- Publication type:
- Article
5
In Situ Measurement of Thermal Strain Development in 420 Stainless Steel Additive Manufactured Metals.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 819, doi. 10.1007/s11340-019-00513-3
- By:
- Publication type:
- Article
6
Analysis of the Material Behavior of 3D Printed Laminates Via FFF.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 871, doi. 10.1007/s11340-019-00511-5
- By:
- Publication type:
- Article
7
Loading Orientation Effects on the Strength Anisotropy of Additively-Manufactured Ti-6Al-4V Alloys under Dynamic Compression.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 829, doi. 10.1007/s11340-019-00506-2
- By:
- Publication type:
- Article
8
Parametric Experimentation on Pantographic Unit Cells Reveals Local Extremum Configuration.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 927, doi. 10.1007/s11340-019-00515-1
- By:
- Publication type:
- Article
9
Experimental Validation of an Additively Manufactured Stiffness-Optimized Short-Fiber Reinforced Composite Clevis Joint.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 859, doi. 10.1007/s11340-019-00514-2
- By:
- Publication type:
- Article
10
A Novel Approach to Increase Dynamic Fracture Toughness of Additively Manufactured Polymer.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 899, doi. 10.1007/s11340-019-00486-3
- By:
- Publication type:
- Article
11
Effect of Filling Pattern on the Tensile and Flexural Mechanical Properties of FDM 3D Printed Products.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 883, doi. 10.1007/s11340-018-00467-y
- By:
- Publication type:
- Article
12
Characterization of the Effects of Internal Pores on Tensile Properties of Additively Manufactured Austenitic Stainless Steel 316L.
- Published in:
- Experimental Mechanics, 2019, v. 59, n. 6, p. 793, doi. 10.1007/s11340-018-00465-0
- By:
- Publication type:
- Article