Dynamic Tensile Testing of Soft Materials.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 451, doi. 10.1007/s11340-008-9133-5
- By:
- Publication type:
- Article
Works matching IS 00144851 AND DT 2009 AND VI 49 AND IP 4
Results: 16
1
2
Experimental Study of Open-Cell Cellular Structures with Elastic Filler Material.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 501, doi. 10.1007/s11340-008-9183-8
- By:
- Publication type:
- Article
3
Quantitative Impact Testing of Energy Dissipation at Surfaces.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 511, doi. 10.1007/s11340-008-9198-1
- By:
- Publication type:
- Article
4
Dynamic Deformation Behavior of a Golf Ball during Normal Impact.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 471, doi. 10.1007/s11340-008-9156-y
- By:
- Publication type:
- Article
5
Study of a Crack at a Fastener Hole by Digital Image Correlation.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 551, doi. 10.1007/s11340-008-9161-1
- By:
- Publication type:
- Article
6
Influence of Horizontal Excitations on Dynamic Stability of a Slender Beam Under Vertical Excitation.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 541, doi. 10.1007/s11340-008-9153-1
- By:
- Publication type:
- Article
7
Design of Inserts for Split-Hopkinson Pressure Bar Testing of Low Strain-to-Failure Materials.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 479, doi. 10.1007/s11340-008-9145-1
- By:
- Publication type:
- Article
8
Error Analysis in Trifilar Inertia Measurements.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 533, doi. 10.1007/s11340-008-9142-4
- By:
- Publication type:
- Article
9
Study on the Use of Motion Compensation Techniques to Determine Heat Sources. Application to Large Deformations on Cracked Rubber Specimens.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 561, doi. 10.1007/s11340-008-9138-0
- By:
- Publication type:
- Article
10
Two Dimensions Residual Stresses Analysis Through Incremental Groove Machining Combined with Electronic Speckle Pattern Interferometry.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 459, doi. 10.1007/s11340-008-9151-3
- By:
- Publication type:
- Article
11
An Experimental Technique for Spalling of Concrete.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 523, doi. 10.1007/s11340-008-9159-8
- By:
- Publication type:
- Article
12
A New Procedure to Measure Near Yield Residual Stresses Using the Deep Hole Drilling Technique.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 595, doi. 10.1007/s11340-008-9164-y
- By:
- Publication type:
- Article
13
Time Average Geometric Moiré—Back to the Basics.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 439, doi. 10.1007/s11340-008-9167-8
- By:
- Publication type:
- Article
14
Planar Strain Measurements on Wood Specimens.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 575, doi. 10.1007/s11340-008-9162-0
- By:
- Publication type:
- Article
15
Reconstruction of Residual Hoop Stress in Railroad Car Wheels Based on Saw Cut Measurements.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 491, doi. 10.1007/s11340-008-9197-2
- By:
- Publication type:
- Article
16
The Effect of Strain Rate, Specimen Geometry and Lubrication on Responses of Aluminium AA2024 in Uniaxial Compression Experiments.
- Published in:
- Experimental Mechanics, 2009, v. 49, n. 4, p. 587, doi. 10.1007/s11340-008-9129-1
- By:
- Publication type:
- Article