Works matching DE "PIPELINE welding"

Results: 52

Ultrasonic control of welded joints in a Du800-type pipeline. Part I: Restoring reflector images by digital focusing with an antenna.

Published in:

Russian Journal of Nondestructive Testing, 2017, v. 53, n. 3, p. 175, doi. 10.1134/S1061830917030020

By:

Bazulin, E.

Publication type:

Article

Numerical Simulation Analysis On Residual Stress Pipeline Girth Welding Joint Strength in Operation Conditions.

Published in:

Arab Gulf Journal of Scientific Research, 2013, v. 31, n. Special, p. 361, doi. 10.51758/agjsr-s1-2013-0026

By:

Peng Zhang;
Linpo Su;
Xianchun Long;
Yonghong Duan

Publication type:

Article

EQUIPMENT FOR PREPARATION OF PIPE ENDS TO WELDING OF POSITION BUTT JOINTS OF PIPELINE.

Published in:

Paton Welding Journal, 2015, n. 9, p. 36, doi. 10.15407/tpwj2015.09.06

By:

LOBANOV, L. M.;
MAKHLIN, N. M.;
SMOLYAKOV, V. K.;
VODOLAZSKY, V. E.;
POPOV, V. E.;
SVIRIDENKO, A. A.

Publication type:

Article

CONCERNING REQUIREMENTS TO IMPACT TOUGHNESS OF JOINTS OF PIPELINES PRODUCED USING FLASH BUTT WELDING.

Published in:

Paton Welding Journal, 2015, n. 2, p. 2, doi. 10.15407/tpwj2015.02.01

By:

KYRIAN, V. I.;
KUCHUK-YATSENKO, S. I.;
KAZYMOV, B. I.

Publication type:

Article

BRAZE-WELDED TUBULAR BILLETS FOR PIPELINES AND HIGH-PRESSURE VESSELS.

Published in:

Paton Welding Journal, 2014, n. 10, p. 38, doi. 10.15407/tpwj2014.10.08

By:

PISMENNY, A. A.;
GUBATYUK, R. S.;
PROKOFIEV, A. S.;
MUZHICHENKO, A. F.;
SHINKARENKO, A. S.

Publication type:

Article

DEVELOPMENT OF TECHNOLOGIES OF REPAIR BY ARC WELDING OF OPERATING MAIN PIPELINES IN UKRAINE.

Published in:

Paton Welding Journal, 2014, n. 5, p. 40, doi. 10.15407/tpwj2014.05.07

By:

BUT, V. S.;
OLEJNIK, O. I.

Publication type:

Article

CALCULATION OF PARAMETERS OF EXPLOSION TREATMENT FOR REDUCTION OF RESIDUAL STRESSES IN CIRCUMFERENTIAL WELDS OF PIPELINES.

Published in:

Paton Welding Journal, 2013, n. 8, p. 31

By:

BRYZGALIN, A. G.

Publication type:

Article

DETERMINATION OF CONTACT PRESSURE OF REINFORCING SLEEVE IN REPAIR OF PIPELINES WITH SURFACE DEFECTS.

Published in:

Paton Welding Journal, 2013, n. 6, p. 11

By:

MAKHNENKO, V. I.;
OLEJNIK, O. I.;
SHEKERA, V. M.

Publication type:

Article

Performing Root Pass Welds on a Super Duplex Stainless Steel Pipeline.

Published in:

Indian Welding Journal, 2015, v. 48, n. 3, p. 72

By:

LAPLANTE, WILLIAM C.

Publication type:

Article

Investigation of the mechanism of formation of cracks after heat treatment of welded joints in Du 850 pipelines of the main circulation circuit made of 10GN2MFA steel, produced by automatic argon-shielded arc welding.

Published in:

Welding International, 2015, v. 29, n. 11, p. 877, doi. 10.1080/09507116.2014.998429

By:

Durynin, V.A.;
Khodakov, V.D.;
Korneyev, A.E.;
Lukicheva, S.V.;
Khodakov, D.V.;
Praliyev, D.A.;
Abrosin, A.A.;
Gudenko, A.S.

Publication type:

Article

Stress corrosion processes in the metal and welded joints in gas pipelines.

Published in:

Welding International, 2014, v. 28, n. 9, p. 717, doi. 10.1080/09507116.2013.852335

By:

Dzioyev, K.M.;
Basiyev, K.D.;
Khabalov, G.I.;
Dzarukayev, E.V.

Publication type:

Article

Potential risk of propagation of defects and welded joints in pipelines in hydrogen sulphide-containing fields.

Published in:

Welding International, 2014, v. 28, n. 9, p. 712, doi. 10.1080/09507116.2013.852334

By:

Koushnarenko, V.M.;
Chirkov, Yu.A.;
Pyataev, A.Ye.;
Schepinov, D.N.

Publication type:

Article

Determination of the dimensions of the heat-affected zone in welding gas pipeline components.

Published in:

Welding International, 2013, v. 27, n. 12, p. 966, doi. 10.1080/09507116.2013.796653

By:

Krasnykh, V.Yu.;
Grigoriev, V.A.;
Patrushev, A.N.;
Tolmachev, Ye M.;
Korolev, V.N.

Publication type:

Article

Design of welded double layer pipelines.

Published in:

Welding International, 2012, v. 26, n. 7, p. 553, doi. 10.1080/09507116.2011.653219

By:

Brovman, T.V.

Publication type:

Article

Efficient methods of preheating in welding joints in pipelines.

Published in:

Welding International, 2012, v. 26, n. 2, p. 155, doi. 10.1080/09507116.2011.600062

By:

Korol'kov, P.M.

Publication type:

Article

Welding of polymer pipes of gas pipelines at low temperatures.

Published in:

Welding International, 2011, v. 25, n. 12, p. 981, doi. 10.1080/09507116.2011.581442

By:

Starostin, N.P.;
Gerasimov, A.I.;
Danzanova, E.V.

Publication type:

Article

Ultra-high-strength linepipe X100-X120.

Published in:

Welding International, 2011, v. 25, n. 9, p. 657, doi. 10.1080/09507116.2010.527043

By:

Ishikawa, Nobuyuki

Publication type:

Article

Theoretical and experimental justification of the repair of transmission oil pipelines using welding methods without interrupting gas pumping.

Published in:

Welding International, 2011, v. 25, n. 2, p. 110, doi. 10.1080/09507116.2010.527085

By:

Steklov, O.I.;
Shafikov, R.;
Sevast'yanov, S.P.

Publication type:

Article

Residual welding stresses in multipass welding of circumferential joints in pipelines.

Published in:

Welding International, 2010, v. 24, n. 8, p. 631, doi. 10.1080/09507111003655549

By:

Ponomareva, I.N.

Publication type:

Article

A method for determining the accuracy of maintaining the welding conditions in resistance spot weldings.

Published in:

Welding International, 2010, v. 24, n. 4, p. 293, doi. 10.1080/09507110903319990

By:

Sidorov, V.P.

Publication type:

Article

Deviation quantification of the intersecting curve weld seam based on non-ideal models.

Published in:

International Journal of Advanced Manufacturing Technology, 2018, v. 97, n. 1-4, p. 1347, doi. 10.1007/s00170-018-2010-1

By:

Liu, Yan;
Shi, Lei;
Tian, Xincheng

Publication type:

Article

Development of a cold stamping process for forming single-welded elbows.

Published in:

International Journal of Advanced Manufacturing Technology, 2017, v. 88, n. 5-8, p. 1911, doi. 10.1007/s00170-016-8930-8

By:

Yu, Gaochao;
Zhao, Jun;
Wang, Chunge;
Zhai, Ruixue;
Ma, Rui

Publication type:

Article

Neutralizing the effect of the angle variations on the drop detachment in automatic GMAW system.

Published in:

International Journal of Advanced Manufacturing Technology, 2011, v. 54, n. 1-4, p. 123, doi. 10.1007/s00170-010-2912-z

By:

Tipi, Alireza

Publication type:

Article

The study on the drop detachment for automatic pipeline GMAW system: short-circuit mode.

Published in:

International Journal of Advanced Manufacturing Technology, 2010, v. 50, n. 1-4, p. 149, doi. 10.1007/s00170-010-2690-7

By:

Tipi, Alireza Doodman

Publication type:

Article

The study on the drop detachment for automatic pipeline GMAW system: free flight mode.

Published in:

International Journal of Advanced Manufacturing Technology, 2010, v. 50, n. 1-4, p. 137, doi. 10.1007/s00170-010-2515-8

By:

Doodman Tipi, Alireza

Publication type:

Article

In-service Repair of the Transmission Pipelines.

Published in:

Petroleum - Gas University of Ploiesti Bulletin, Technical Series, 2010, v. 62, n. 2, p. 9

By:

Zecheru, Gheorghe;
Drăghici, Gheorghe;
Laţa, Ilie E.;
Diniţă, Alin

Publication type:

Article

A review of the role and effect of residual stress on pipeline-flaw assessment.

Published in:

Journal of Pipeline Engineering, 2014, v. 13, n. 4, p. 265

By:

Al-Owaisi, Sultan Salim;
Becker, Adib;
Wei Sun

Publication type:

Article

Welding on in-service gas pipelines using low-yield electrodes.

Published in:

Journal of Pipeline Engineering, 2013, v. 12, n. 1, p. 29

By:

Schipaanboord, Wim N.;
Marquering, Jan;
Koppens, Bart G.;
Spiekhout, Jan

Publication type:

Article

Modified WIC test: an efficient and effective tool for evaluating pipeline girth weldability.

Published in:

Science & Technology of Welding & Joining, 2017, v. 22, n. 4, p. 287, doi. 10.1080/13621718.2016.1232674

By:

Kurji, R.;
Coniglio, N.;
Griggs, J.;
Ghomashchi, R.

Publication type:

Article

Challenges and developments in pipeline weldability and mechanical properties.

Published in:

Science & Technology of Welding & Joining, 2013, v. 18, n. 2, p. 169, doi. 10.1179/1362171812Y.0000000090

By:

Liu, C;
Bhole, S D

Publication type:

Article

Measured residual stresses and integrity of pipeline girth welds.

Published in:

Science & Technology of Welding & Joining, 2012, v. 17, n. 8, p. 694, doi. 10.1179/1362171812Y.0000000064

By:

Law, M;
Luzin, V

Publication type:

Article

Influence of forge pressure on properties of friction welded pipelines using intermediate ring.

Published in:

Science & Technology of Welding & Joining, 2008, v. 13, n. 5, p. 445, doi. 10.1179/174329308X341870

By:

Faes, K.;
Vermeirsch, W.;
De Baets, P.;
Denys, R.;
Van Der Donckt, E.

Publication type:

Article

Hardness prediction models based on HAZ simulation for in-service welded pipeline steels.

Published in:

Science & Technology of Welding & Joining, 2005, v. 10, n. 6, p. 681, doi. 10.1179/174329305X65069

By:

Nolan, D.;
Sterjovski, Z.;
Dunne, D.

Publication type:

Article

Root pass solidification cracking in low carbon pipeline girth welds deposited via cellulosic manual metal arc welding.

Published in:

Science & Technology of Welding & Joining, 2003, v. 8, n. 2, p. 102, doi. 10.1179/136217103225008928

By:

Nolan, D.;
Dunne, D.;
Norrish, J.

Publication type:

Article

Experience in the demagnetization of large objects.

Published in:

Russian Journal of Nondestructive Testing, 2010, v. 46, n. 5, p. 315, doi. 10.1134/S1061830910050013

By:

Shelikhov, G.

Publication type:

Article

Development of the main requirements for contemporary systems of radiographic testing including digital image processing taking into account specific features of inspection of welded joints of oil and gas pipelines (a review).

Published in:

Russian Journal of Nondestructive Testing, 2008, v. 44, n. 3, p. 215, doi. 10.1134/S106183090803008X

By:

Alekhnovich, E.;
Van’kova, N.;
Kapustin, V.;
Karpenko, A.;
Maksimova, T.

Publication type:

Article

HOW TO PEREVENT DAMAGES OF TRANSPORTING PIPELINE GIRTH WELDS?

Published in:

Multidiszciplináris Tudományok, 2021, v. 11, n. 4, p. 208, doi. 10.35925/j.multi.2021.4.25

By:

Dakhel, Ahmad Yasser;
Lukács, János

Publication type:

Article

Finite element analysis of the offshore reel-laying operations for double-walled pipe.

Published in:

Advances in Mechanical Engineering (Sage Publications Inc.), 2017, v. 9, n. 10, p. 1, doi. 10.1177/1687814017731226

By:

Jong Rae Cho;
Byeong Don Joo;
Jin Rae Cho;
Young Hoon Moon

Publication type:

Article

Safety monitoring of continuously welded pipeline subjected to ground deformation using wireless micro-electro-mechanical system inclinometers.

Published in:

Advances in Mechanical Engineering (Sage Publications Inc.), 2017, v. 9, n. 9, p. 1, doi. 10.1177/1687814017715194

By:

Suzhen Li;
Naihui Gao

Publication type:

Article

PART 8: USE OF SMALL-SCALE PIPELINE SPECIMENS TO TEST A STEEL-ADHESIVE REPAIR SYSTEM.

Published in:

Experimental Techniques, 2007, v. 31, n. 6, p. 64, doi. 10.1111/j.1747-1567.2007.00270.x

By:

Perez Rosas, M.A.;
Vieira, R.D.;
Freire, J.L.F.

Publication type:

Article

Using thermovision inspection in the welding of polyethylene pipes.

Published in:

Technical Diagnostics & Non-Destructive Testing, 2010, n. 1, p. 59

By:

Glukhovskii, V. Yu.;
Kostenko, A. V.

Publication type:

Article

Application of Cold Wire Gas Metal Arc Welding for Narrow Gap Welding (NGW) of High Strength Low Alloy Steel.

Published in:

Materials (1996-1944), 2019, v. 12, n. 3, p. 335, doi. 10.3390/ma12030335

By:

Ribeiro, Rafael A.;
Assunção, Paulo D. C.;
Dos Santos, Emanuel B. F.;
Filho, Ademir A. C.;
Braga, Eduardo M.;
Gerlich, Adrian P.

Publication type:

Article

Intelligent Control of Welding Gun Pose for Pipeline Welding Robot Based on Improved Radial Basis Function Network and Expert System.

Published in:

International Journal of Advanced Robotic Systems, 2013, v. 10, n. 2, p. 1, doi. 10.5772/55662

By:

Jingwen Tian;
Meijuan Gao;
Yonggang He

Publication type:

Article

Thermal Analysis of In-Service Welding Process for Pipeline.

Published in:

Journal of Petroleum Research & Studies, 2019, n. 22, p. E1

By:

Amori, Karima E.;
Hussain, Mohamed N.;
Hilal, Hadeel B.

Publication type:

Article

Fatigue surface crack propagation and intersecting cracks in connection with welding residual stresses.

Published in:

Fatigue & Fracture of Engineering Materials & Structures, 2018, v. 41, n. 10, p. 2140, doi. 10.1111/ffe.12808

By:

Chernyatin, A. S.;
Matvienko, Yu.G.;
Razumovsky, I. A.

Publication type:

Article

Effect of Hyperbaric Chamber Gas on Transformation Texture of the API-X70 Pipeline Weld Metal.

Published in:

Metallurgical & Materials Transactions. Part A, 2012, v. 43, n. 9, p. 3162, doi. 10.1007/s11661-012-1157-x

By:

Azar, Amin;
Østby, Erling;
Akselsen, Odd

Publication type:

Article

A novel above-ground marking approach based on the girth weld impact sound for pipeline defect inspection.

Published in:

Insight: Non-Destructive Testing & Condition Monitoring, 2014, v. 56, n. 12, p. 677, doi. 10.1784/insi.2014.56.12.677

By:

Li, Yibo;
Liu, Shuangsai;
Dorantes-Gonzalez, D J;
Zhou, Chunyao;
Zhu, Huiyu

Publication type:

Article

Improved focusing for thick-wall pipeline girth weld inspections using phased arrays.

Published in:

Insight: Non-Destructive Testing & Condition Monitoring, 2005, v. 47, n. 12, p. 769, doi. 10.1784/insi.2005.47.12.769

By:

Moles, M;
Labbé, S;
Zhang, J

Publication type:

Article

Experimental Study and Computer Simulation of the Effect of Spider Shape on the Weld-Lines in...

Published in:

Polymer Engineering & Science, 1998, v. 38, n. 9, p. 1506, doi. 10.1002/pen.10321

By:

Huang, Y.;
Prentice, P.

Publication type:

Article

Influence of peak temperature during in-service welding of API X70 pipeline steels on microstructure and fracture energy of the reheated coarse grain heat-affected zones.

Published in:

Journal of Materials Science, 2011, v. 46, n. 19, p. 6424, doi. 10.1007/s10853-011-5592-7

By:

Chaowen Li;
Yong Wang;
Yuhua Chen

Publication type:

Article