Linear and nonlinear flexural analysis of higher-order shear deformation laminated plates with circular delamination.
- Published in:
- Acta Mechanica, 2018, v. 229, n. 4, p. 1631, doi. 10.1007/s00707-017-2072-4
- By:
- Publication type:
- Article
Works about LAMINATED material manufacturing
Results: 15
1
2
Editorial corner -- a personal view Interleaving in structural composites: Adapting an old concept to new challenges.
- Published in:
- 2018
- By:
- Publication type:
- Editorial
3
Graphite-high density polyethylene laminated composites with high thermal conductivity made by filament winding.
- Published in:
- Express Polymer Letters, 2018, v. 12, n. 3, p. 215, doi. 10.3144/expresspolymlett.2018.20
- By:
- Publication type:
- Article
4
Low-cost, environmentally friendly route for producing CFRP laminates with microfibrillated cellulose interphase.
- Published in:
- Express Polymer Letters, 2017, v. 11, n. 1, p. 47, doi. 10.3144/expresspolymlett.2017.6
- By:
- Publication type:
- Article
5
Fabrication of laminated-metal composite tubes by multi-billet rotary swaging technique.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2015, v. 76, n. 1-4, p. 713, doi. 10.1007/s00170-014-6302-9
- By:
- Publication type:
- Article
6
Curing behavior and processability of BMI/3-APN system for advanced glass fiber composite laminates.
- Published in:
- Journal of Applied Polymer Science, 2016, v. 133, n. 27, p. n/a, doi. 10.1002/app.43640
- By:
- Publication type:
- Article
7
Influence of Soluble Electrospun Co‐Polyethersulfone Veils on Dynamic Mechanical and Morphological Properties of Epoxy Composites: Effect of Polymer Molar Mass.
- Published in:
- Advances in Polymer Technology, 2018, v. 37, n. 3, p. 798, doi. 10.1002/adv.21723
- By:
- Publication type:
- Article
8
Sag Bending Control in the Production of Automobile Windshields.
- Published in:
- Glass & Ceramics, 2018, v. 74, n. 11/12, p. 432, doi. 10.1007/s10717-018-0010-0
- By:
- Publication type:
- Article
9
Sensitivity of Automated Fibre Placement Parameters on Manufacturing Defects in Laminated Composites.
- Published in:
- International Journal of Vehicle Structures & Systems (IJVSS), 2012, v. 4, n. 4, p. 132, doi. 10.4273/ijvss.4.4.03
- By:
- Publication type:
- Article
10
Defect reduction strategies for the manufacture of contoured laminates using vacuum BAG-only prepregs.
- Published in:
- Polymer Composites, 2017, v. 38, n. 9, p. 2016, doi. 10.1002/pc.23773
- By:
- Publication type:
- Article
11
Multiscale Collaborative Optimization of Processing Parameters for Carbon Fiber/Epoxy Laminates Fabricated by High-Speed Automated Fiber Placement.
- Published in:
- Advances in Materials Science & Engineering, 2016, p. 1, doi. 10.1155/2016/5480352
- By:
- Publication type:
- Article
12
A novel fiber–veneer-laminated composite based on tannin resin.
- Published in:
- Journal of Adhesion, 2017, v. 93, n. 6, p. 461, doi. 10.1080/00218464.2015.1084233
- By:
- Publication type:
- Article
13
LAMINATED OBJECT MANUFACTURING-LOM.
- Published in:
- Fiability & Durability / Fiabilitate si Durabilitate, 2011, n. 2, p. 55
- By:
- Publication type:
- Article
14
Identification of the lamination stack's behavior simulated with a multi-scale homogenization using a progressive contact formulation.
- Published in:
- PAMM: Proceedings in Applied Mathematics & Mechanics, 2014, v. 14, n. 1, p. 253, doi. 10.1002/pamm.201410114
- By:
- Publication type:
- Article
15
ROTOR DESIGN AND OPTIMIZATION OF SYNCHRONOUS RELUCTANCE MACHINE.
- Published in:
- MM Science Journal, 2015, p. 555, doi. 10.17973/mmsj.2015_03_201504
- By:
- Publication type:
- Article