Works matching DE "INJECTION blow molding"
Results: 18
Analysis of the Water Assisted Injection Technique by Using Ultrasonic.
- Published in:
- Progress in Rubber, Plastics & Recycling Technology, 2013, v. 29, n. 1, p. 55, doi. 10.1177/147776061302900104
- By:
- Publication type:
- Article
One- and two-component micro powder injection moulding derived from thermoplastic microreplication.
- Published in:
- Plastics, Rubber & Composites, 2010, v. 39, n. 7, p. 287, doi. 10.1179/174328910X12691245470310
- By:
- Publication type:
- Article
Two-component microinjection moulding for MID fabrication.
- Published in:
- Plastics, Rubber & Composites, 2010, v. 39, n. 7, p. 300, doi. 10.1179/174328910X12691245470356
- By:
- Publication type:
- Article
New aspects of process induced properties of microinjection moulded parts.
- Published in:
- Plastics, Rubber & Composites, 2010, v. 39, n. 7, p. 308, doi. 10.1179/174328910X12691245470392
- By:
- Publication type:
- Article
Warpage and countermeasure for injection-molded in-mold labeling parts.
- Published in:
- Polymer Engineering & Science, 2011, v. 51, n. 3, p. 411, doi. 10.1002/pen.21849
- By:
- Publication type:
- Article
The unique flow of polypropylene at the weld line behind an obstacle in injection molding.
- Published in:
- Polymer Engineering & Science, 2011, v. 51, n. 3, p. 526, doi. 10.1002/pen.21841
- By:
- Publication type:
- Article
Using Multiobjective Evolutionary Algorithms in the Optimization of Operating Conditions of Polymer Injection Molding.
- Published in:
- Polymer Engineering & Science, 2010, v. 50, n. 8, p. 1667, doi. 10.1002/pen.21652
- By:
- Publication type:
- Article
The Effect of Injection Molding Conditions on the Morphology of Polymer Structural Foams.
- Published in:
- Polymer Engineering & Science, 2009, v. 49, n. 5, p. 949, doi. 10.1002/pen.21283
- By:
- Publication type:
- Article
A Modeling Approach to the Effect of Resin Characteristics on Parison Formation in Extrusion Blow Molding.
- Published in:
- Polymer Engineering & Science, 2009, v. 49, n. 2, p. 251, doi. 10.1002/pen.21251
- By:
- Publication type:
- Article
An Inverse Estimation of Initial Temperature Profile in a Polymer Process.
- Published in:
- Polymer Engineering & Science, 2008, v. 48, n. 1, p. 133, doi. 10.1002/pen.20930
- By:
- Publication type:
- Article
Rheology Studies of Foam Flow During Injection Mold Filling.
- Published in:
- Polymer Engineering & Science, 2007, v. 47, n. 4, p. 522, doi. 10.1002/pen.20730
- By:
- Publication type:
- Article
Editorial corner - a personal view Is there any chance for polypropylene/clay nanocomposites in injection molding?
- Published in:
- 2011
- By:
- Publication type:
- Editorial
Emission Reduction in a Direct Injection Diesel Engine Fueled by Neem-Diesel Blend.
- Published in:
- Energy Sources Part A: Recovery, Utilization & Environmental Effects, 2009, v. 31, n. 6, p. 500, doi. 10.1080/15567030701715542
- By:
- Publication type:
- Article
Mold surface roughness effects on cavity filling of polymer melt in micro injection molding.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2008, v. 37, n. 11/12, p. 1105, doi. 10.1007/s00170-007-1060-6
- By:
- Publication type:
- Article
Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2007, v. 35, n. 5/6, p. 468, doi. 10.1007/s00170-006-0739-4
- By:
- Publication type:
- Article
Three-dimensional modeling of roughness effects on microthickness filling in injection mold cavity.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 45, n. 5/6, p. 481, doi. 10.1007/s00170-009-1984-0
- By:
- Publication type:
- Article
The liquid crystal injection scheduling problem (LCISP).
- Published in:
- International Journal of Production Research, 2011, v. 49, n. 2, p. 467, doi. 10.1080/00207540903443261
- By:
- Publication type:
- Article
Advances in infrared technology for the online monitoring of injection moulding: application to the understanding of the nature of contact at the polymer-mould interface.
- Published in:
- Transactions of the Institute of Measurement & Control, 2007, v. 29, n. 5, p. 431, doi. 10.1177/0142331207075587
- By:
- Publication type:
- Article