Found: 209
Select item for more details and to access through your institution.
An investigation of the microstructure and tribological behavior of polyether ether ketone composites fabricated by extrusion‐based additive manufacturing.
- Published in:
- Polymer International, 2024, v. 73, n. 7, p. 516, doi. 10.1002/pi.6624
- By:
- Publication type:
- Article
A novel three-dimensional nonlinear unified failure criterion for rock materials.
- Published in:
- Acta Geotechnica, 2024, v. 19, n. 6, p. 3337, doi. 10.1007/s11440-023-02114-w
- By:
- Publication type:
- Article
Manufacturing ODS Steels from GARS Powders by Friction Consolidation and Extrusion.
- Published in:
- JOM: The Journal of The Minerals, Metals & Materials Society (TMS), 2024, v. 76, n. 6, p. 2899, doi. 10.1007/s11837-024-06584-5
- By:
- Publication type:
- Article
Effects of the Extrusion Ratio on the Microstructure and Mechanical Properties of Columnar Network Structured TiBw/TA15 Composites.
- Published in:
- JOM: The Journal of The Minerals, Metals & Materials Society (TMS), 2024, v. 76, n. 5, p. 2231, doi. 10.1007/s11837-024-06380-1
- By:
- Publication type:
- Article
Effect of Multistage Solution Aging Heat Treatment on Mechanical Properties and Precipitated Phase Characteristics of High-Strength Toughened 7055 Alloy.
- Published in:
- Materials (1996-1944), 2024, v. 17, n. 8, p. 1754, doi. 10.3390/ma17081754
- By:
- Publication type:
- Article
Quantitative Comparative Study on the Performance of a Valve-Controlled Actuator and Electro-Hydrostatic Actuator.
- Published in:
- Actuators, 2024, v. 13, n. 4, p. 118, doi. 10.3390/act13040118
- By:
- Publication type:
- Article
Effect of Hot Deformation and Heat Treatment on the Microstructure and Properties of Spray-Formed Al-Zn-Mg-Cu Alloys.
- Published in:
- Metals (2075-4701), 2024, v. 14, n. 4, p. 451, doi. 10.3390/met14040451
- By:
- Publication type:
- Article
A DFT study of the electronic structure, optical and thermoelectric properties of perovskite CsSnBr<sub>3</sub> compound under strains effect: Photovoltaic applications.
- Published in:
- Modern Physics Letters B, 2024, v. 38, n. 7, p. 1, doi. 10.1142/S0217984923502378
- By:
- Publication type:
- Article
New Method for Detecting Flange Fracture Initiation in Incremental Radial Extrusion.
- Published in:
- Materials (1996-1944), 2024, v. 17, n. 5, p. 1054, doi. 10.3390/ma17051054
- By:
- Publication type:
- Article
Research on the New Hydrostatic Transmission System of Wheel Loaders Based on Fuzzy Sliding Mode Control.
- Published in:
- Energies (19961073), 2024, v. 17, n. 3, p. 565, doi. 10.3390/en17030565
- By:
- Publication type:
- Article
Study of the Dynamic Properties of the Miniature Electro-Hydrostatic Actuator.
- Published in:
- Machines, 2024, v. 12, n. 2, p. 114, doi. 10.3390/machines12020114
- By:
- Publication type:
- Article
A Bimodal Hydrostatic Actuator for Robotic Legs with Compliant Fast Motion and High Lifting Force.
- Published in:
- Actuators, 2023, v. 12, n. 12, p. 452, doi. 10.3390/act12120452
- By:
- Publication type:
- Article
Solidification and Conformation of Ionic Liquid 1-Ethyl-3-Methylimidazolium Trifluoroacetate under High Pressure.
- Published in:
- International Journal of Heat & Technology, 2023, v. 41, n. 6, p. 1639, doi. 10.18280/ijht.410627
- By:
- Publication type:
- Article
Properties of cement‐based materials containing calcium stearate and supplementary cementitious materials.
- Published in:
- Structural Concrete, 2023, v. 24, n. 6, p. 7445, doi. 10.1002/suco.202300152
- By:
- Publication type:
- Article
Design and Experimental Assessment of a Vibration Control System Driven by Low Inertia Hydrostatic Magnetorheological Actuators for Heavy Equipment.
- Published in:
- Actuators, 2023, v. 12, n. 11, p. 407, doi. 10.3390/act12110407
- By:
- Publication type:
- Article
Tolerance of Al–Mg–Si Wrought Alloys for High Fe Contents: The Role of Effective Si.
- Published in:
- Metallurgical & Materials Transactions. Part A, 2023, v. 54, n. 11, p. 4472, doi. 10.1007/s11661-023-07180-z
- By:
- Publication type:
- Article
Interrelationships between process parameters, cross‐sectional geometry, fracture behavior, and mechanical properties in material extrusion additive manufacturing.
- Published in:
- Polymer Engineering & Science, 2023, v. 63, n. 11, p. 3906, doi. 10.1002/pen.26495
- By:
- Publication type:
- Article
Water-Weakening and Time-Dependent Deformation of Organic-Rich Chalks.
- Published in:
- Rock Mechanics & Rock Engineering, 2023, v. 56, n. 11, p. 8041, doi. 10.1007/s00603-023-03453-6
- By:
- Publication type:
- Article
新型静压支承结构液压缸力学性能分析与实验.
- Published in:
- Machine Tool & Hydraulics, 2023, v. 51, n. 20, p. 93, doi. 10.3969/j.issn.1001-3881.2023.20.015
- By:
- Publication type:
- Article
Thermo-Mechanical Treatment for Reducing the Wear Rate of CuCrZr Tool Electrodes during Electro-Discharge Machining.
- Published in:
- Materials (1996-1944), 2023, v. 16, n. 20, p. 6787, doi. 10.3390/ma16206787
- By:
- Publication type:
- Article
Effect of microstructure refinement of pure copper on improving the performance of electrodes in electro discharge machining (EDM).
- Published in:
- Scientific Reports, 2023, v. 13, n. 1, p. 1, doi. 10.1038/s41598-023-43584-y
- By:
- Publication type:
- Article
Selection of Design Scheme for an Ultrahigh-Pressure Hydrostatic Extrusion Cylinder.
- Published in:
- Actuators, 2023, v. 12, n. 10, p. 369, doi. 10.3390/act12100369
- By:
- Publication type:
- Article
Microstructure, mechanical properties and work hardening behavior of SiC<sub>p</sub>/2024Al composite sheet.
- Published in:
- Journal of Aeronautical Materials, 2023, v. 43, n. 5, p. 20, doi. 10.11868/j.issn.1005-5053.2022.000114
- By:
- Publication type:
- Article
Simulation-Based Identification of Operating Point Range for a Novel Laser-Sintering Machine for Additive Manufacturing of Continuous Carbon-Fibre-Reinforced Polymer Parts.
- Published in:
- Polymers (20734360), 2023, v. 15, n. 19, p. 3975, doi. 10.3390/polym15193975
- By:
- Publication type:
- Article
Self-Organization of Various-Scale Structural Groups in a Cu/NbTi Composite under the Effect of Hydrostatic Bundle Extrusion.
- Published in:
- Inorganic Materials, 2023, v. 59, n. 9, p. 932, doi. 10.1134/S0020168523090121
- By:
- Publication type:
- Article
Influence of extrusion pressures on shape memory properties of carbon fiber/basalt fiber hybrid composites with graphene oxide fabricated by the vacuum infiltration hot pressing system.
- Published in:
- Polymer Composites, 2023, v. 44, n. 9, p. 5910, doi. 10.1002/pc.27536
- By:
- Publication type:
- Article
The Effect of Microstructural Defects on High-Cycle Fatigue of Ti Grade 2 Manufactured by PBF-LB and Hydrostatic Extrusion.
- Published in:
- Crystals (2073-4352), 2023, v. 13, n. 8, p. 1250, doi. 10.3390/cryst13081250
- By:
- Publication type:
- Article
Investigation of the impact of the short fiber reinforcements on the thermal and mechanical properties of polymer-based composites manufactured by material extrusion.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 127, n. 7/8, p. 3801, doi. 10.1007/s00170-023-11758-7
- By:
- Publication type:
- Article
Influence of extrusion method on the microstructure and mechanical properties of formed magnesium alloy tubes.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 127, n. 7/8, p. 3979, doi. 10.1007/s00170-023-11708-3
- By:
- Publication type:
- Article
Microstructure and Mechanical Properties of Al-Si Alloys Produced by Rapid Solidification and Hot Extrusion.
- Published in:
- Materials (1996-1944), 2023, v. 16, n. 15, p. 5223, doi. 10.3390/ma16155223
- By:
- Publication type:
- Article
Mechanical and thermal properties of polyamide‐6 nanocomposites reinforced by graphene oxide with low loading by double extrusion method.
- Published in:
- Polymers for Advanced Technologies, 2023, v. 34, n. 8, p. 2788, doi. 10.1002/pat.6102
- By:
- Publication type:
- Article
Effect of Interface Friction on Surface Integrity and Microstructure during Extrusion of Pure Nickel.
- Published in:
- Advanced Engineering Materials, 2023, v. 25, n. 14, p. 1, doi. 10.1002/adem.202201684
- By:
- Publication type:
- Article
A Study on Mechanical Properties of Low-Cost Thermoplastic-Based Materials for Material Extrusion Additive Manufacturing.
- Published in:
- Polymers (20734360), 2023, v. 15, n. 14, p. 2981, doi. 10.3390/polym15142981
- By:
- Publication type:
- Article
REVIEW ON DESIGN AND ADDITIVE MANUFACTURING OF CELLULAR LATTICE STRUCTURES BY EXTRUSION TECHNOLOGIES.
- Published in:
- Academic Journal of Manufacturing Engineering, 2023, v. 21, n. 3, p. 118
- By:
- Publication type:
- Article
Investigation of Metal Structure Formation During Ingotless Rolling-Extrusion of Aluminum and Its Alloys.
- Published in:
- Metallurgist, 2023, v. 67, n. 3/4, p. 497, doi. 10.1007/s11015-023-01541-0
- By:
- Publication type:
- Article
Effect of Initial Microstructure Prior to Extrusion on the Microstructure and Mechanical Properties of Extruded AZ80 Alloy with a Low Temperature and a Low Ratio.
- Published in:
- Chinese Journal of Mechanical Engineering, 2023, v. 36, n. 1, p. 1, doi. 10.1186/s10033-023-00901-w
- By:
- Publication type:
- Article
Verification Analysis of X70 Type B Sleeve for In-service Pipeline Repair.
- Published in:
- Journal of Failure Analysis & Prevention, 2023, v. 23, n. 3, p. 1137, doi. 10.1007/s11668-023-01655-2
- By:
- Publication type:
- Article
Stability and infinite static stiffness of hydrostatic lead screw compensated with a single-action membrane restrictor.
- Published in:
- Nonlinear Dynamics, 2023, v. 111, n. 11, p. 9971, doi. 10.1007/s11071-023-08379-w
- By:
- Publication type:
- Article
Flexible Electromagnetic Shielding Nano-Composites Based on Silicon and NiFe 2 O 4 Powders.
- Published in:
- Polymers (20734360), 2023, v. 15, n. 11, p. 2447, doi. 10.3390/polym15112447
- By:
- Publication type:
- Article
Numerical simulation and experiment study on hot extrusion process of 18Ni (250) maraging steel large fan shaft for aero-engines.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 126, n. 5/6, p. 2371, doi. 10.1007/s00170-023-11301-8
- By:
- Publication type:
- Article
Cascade active disturbance rejection control of single‐rod electrohydrostatic actuator.
- Published in:
- Asian Journal of Control, 2023, v. 25, n. 3, p. 1888, doi. 10.1002/asjc.2815
- By:
- Publication type:
- Article
Effects of HE and ECAP processes on changes in microstructure and mechanical properties in copper, iron and zinc.
- Published in:
- Bulletin of the Polish Academy of Sciences: Technical Sciences, 2023, v. 71, n. 3, p. 1, doi. 10.24425/bpasts.2023.145563
- By:
- Publication type:
- Article
Structural Hierarchy of PA6 Macromolecules after Hydrostatic Extrusion.
- Published in:
- Materials (1996-1944), 2023, v. 16, n. 9, p. 3435, doi. 10.3390/ma16093435
- By:
- Publication type:
- Article
Effect of the Second Phases on Composite Spinning-Extrusion Forming and Mechanical Properties of Al–Cu–Li Alloy.
- Published in:
- Materials (1996-1944), 2023, v. 16, n. 9, p. 3573, doi. 10.3390/ma16093573
- By:
- Publication type:
- Article
Influence of material modification and fillers on the dimensional stability and warpage of polypropylene in screw‐extrusion‐based large area additive manufacturing.
- Published in:
- Polymer Engineering & Science, 2023, v. 63, n. 5, p. 1598, doi. 10.1002/pen.26309
- By:
- Publication type:
- Article
Achieving effective interlayer bonding of PLA parts during the material extrusion process with enhanced mechanical properties.
- Published in:
- Scientific Reports, 2023, v. 13, n. 1, p. 1, doi. 10.1038/s41598-023-33510-7
- By:
- Publication type:
- Article
Influence of Pre-Heat Treatment on the Deformation Behaviors, Microstructural Characteristics, and Mechanical Properties of a Continuously Cast Al-Cu-Mg Alloy during Continuous Extrusion Process.
- Published in:
- Materials (1996-1944), 2023, v. 16, n. 8, p. 3042, doi. 10.3390/ma16083042
- By:
- Publication type:
- Article
Processing PLA/P(3HB)(4HB) blends for the manufacture of highly transparent, gas barrier and fully bio‐based films for compostable packaging applications.
- Published in:
- Journal of Applied Polymer Science, 2023, v. 140, n. 13, p. 1, doi. 10.1002/app.53669
- By:
- Publication type:
- Article
Relationship between Cluster-Arranged Nanoplate Formation and Mechanical Properties of Dilute Mg-Y-Zn Alloys Prepared by Combination of Low-Cooling-Rate Solidification and Extrusion Techniques.
- Published in:
- Materials Transactions, 2023, v. 64, n. 4, p. 756, doi. 10.2320/matertrans.MT-MD2022015
- By:
- Publication type:
- Article
Prediction of Recrystallization Structure of 2A12 Aluminum Alloy Pipe Extrusion Process Based on BP Neural Network.
- Published in:
- Metals (2075-4701), 2023, v. 13, n. 4, p. 664, doi. 10.3390/met13040664
- By:
- Publication type:
- Article