Found: 52
Select item for more details and to access through your institution.
Experimental study on magnetic ball-assisted magnetic abrasive finishing for irregular spherical internal cavity of waveguide formed by selective laser melting.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2024, v. 133, n. 3/4, p. 1417, doi. 10.1007/s00170-024-13805-3
- By:
- Publication type:
- Article
Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting.
- Published in:
- Materials (1996-1944), 2024, v. 17, n. 7, p. 1523, doi. 10.3390/ma17071523
- By:
- Publication type:
- Article
Investigation on the preparation and finishing performance of a novel nanoparticle-enhanced bonded magnetic abrasive.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 129, n. 9/10, p. 4631, doi. 10.1007/s00170-023-12638-w
- By:
- Publication type:
- Article
Time-varying thermoelastic coupling analysis of heat source of ball screw feed drive system.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 129, n. 1/2, p. 923, doi. 10.1007/s00170-023-12352-7
- By:
- Publication type:
- Article
Surface and property characterization of selective laser-melted Ti-6Al-4V alloy after laser polishing.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 128, n. 1/2, p. 703, doi. 10.1007/s00170-023-11880-6
- By:
- Publication type:
- Article
An Assembly Man‑Hour Estimation Model Based on GA‑SVM for Multi‑specification and Small‑Batch Production.
- Published in:
- Transactions of Nanjing University of Aeronautics & Astronautics, 2023, v. 40, n. 4, p. 500, doi. 10.16356/j.1005‑1120.2023.04.010
- By:
- Publication type:
- Article
Generation of micro-channel on PDMS substrate by cryogenic micro-abrasive air-jet machining.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 127, n. 5/6, p. 3003, doi. 10.1007/s00170-023-11719-0
- By:
- Publication type:
- Article
Reaction Mechanism of Combustion Synthesized ZrC2ZrB<sub>2</sub>- Based Cu Cermets.
- Published in:
- Materials Transactions, 2023, v. 64, n. 6, p. 1199, doi. 10.2320/matertrans.MT-M2022210
- By:
- Publication type:
- Article
Controllable preparation of non-uniform tool edges by magnetorheological finishing.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 125, n. 9/10, p. 4119, doi. 10.1007/s00170-023-11019-7
- By:
- Publication type:
- Article
A posture detection method for augmented reality–aided assembly based on YOLO-6D.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 125, n. 7/8, p. 3385, doi. 10.1007/s00170-023-10964-7
- By:
- Publication type:
- Article
Modeling and simulation of the action mechanism of multi-particles in magnetic abrasive finishing for internal blind cavity using the discrete element method.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 125, n. 3/4, p. 1179, doi. 10.1007/s00170-022-10736-9
- By:
- Publication type:
- Article
Investigating the mechanical properties of epoxy resin composites modified by polyamide and nano‐Al<sub>2</sub>O<sub>3</sub>.
- Published in:
- Journal of Applied Polymer Science, 2023, v. 140, n. 11, p. 1, doi. 10.1002/app.53624
- By:
- Publication type:
- Article
Development of erosion equations for removal of organic coating on carbon fiber reinforced polymer surface by plastic abrasive.
- Published in:
- Journal of Coatings Technology & Research, 2023, v. 20, n. 2, p. 671, doi. 10.1007/s11998-022-00700-3
- By:
- Publication type:
- Article
Digital map and probability compensation model for repeated positioning error of feed axis.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2023, v. 124, n. 7/8, p. 2631, doi. 10.1007/s00170-022-10698-y
- By:
- Publication type:
- Article
EBSD and Raman Spectroscopy Analysis of Copper Alloy H62/GOp-modified Layer Prepared by Friction Stir Surface Processing.
- Published in:
- Materials Science / Medziagotyra, 2023, v. 29, n. 1, p. 27, doi. 10.5755/j02.ms.30239
- By:
- Publication type:
- Article
Effect of contact states in the tube on the push bending with low-melting-point alloy as filling medium.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2022, v. 123, n. 11/12, p. 4277, doi. 10.1007/s00170-022-10266-4
- By:
- Publication type:
- Article
Simulation and Experimental Research about Temperature Fields of PDMS Cooled by Liquid Nitrogen Jet Impingement.
- Published in:
- China Mechanical Engineering, 2022, v. 33, n. 18, p. 2161, doi. 10.3969/j.issn.1004-132X.2022.18.002
- By:
- Publication type:
- Article
Finite element simulation and experimental study of single-laser track in laser polishing of Ti6Al4V.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2022, v. 121, n. 7/8, p. 4571, doi. 10.1007/s00170-022-09664-5
- By:
- Publication type:
- Article
Erosion mechanism and damage behavior of CFRP in plastic abrasive jet machining.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2022, v. 121, n. 7/8, p. 4905, doi. 10.1007/s00170-022-09667-2
- By:
- Publication type:
- Article
Modeling and Experimental Verification of Surface Roughness for Grinding Monocrystalline Silicon Lens.
- Published in:
- Advanced Theory & Simulations, 2022, v. 5, n. 7, p. 1, doi. 10.1002/adts.202100422
- By:
- Publication type:
- Article
Experimental investigations of machining characteristics on polydimethylsiloxane (PDMS) by cryogenic abrasive air-jet machining.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2022, v. 118, n. 7/8, p. 2711, doi. 10.1007/s00170-021-08147-3
- By:
- Publication type:
- Article
Experimental study on machining germanium wafer with ice particle, fixed abrasive tools.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2021, v. 115, n. 9/10, p. 3225, doi. 10.1007/s00170-021-07352-4
- By:
- Publication type:
- Article
Effect of Pre-Strain on Microstructure and Tensile Properties of Ti-6Al-4V at Elevated Temperature.
- Published in:
- Metals (2075-4701), 2021, v. 11, n. 8, p. 1321, doi. 10.3390/met11081321
- By:
- Publication type:
- Article
Prediction of erosion volume of PDMS by cryogenic micro-abrasive jet machining based on dimensional analysis method and experimental verification.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2021, v. 114, n. 7/8, p. 2447, doi. 10.1007/s00170-021-07020-7
- By:
- Publication type:
- Article
Study on EDM technology of distributed group electrodes in titanium alloy with large inclined angle and thin-walled group holes.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2021, v. 113, n. 1/2, p. 131, doi. 10.1007/s00170-020-06522-0
- By:
- Publication type:
- Article
Laser polishing of additive manufactured Ti6Al4V alloy: a review.
- Published in:
- Optical Engineering, 2021, v. 60, n. 2, p. 20901, doi. 10.1117/1.OE.60.2.020901
- By:
- Publication type:
- Article
Influences on the extended length and performance of push bending for the GH4169 superalloy tube with small bending radius of 1D.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2021, v. 112, n. 1/2, p. 107, doi. 10.1007/s00170-020-06276-9
- By:
- Publication type:
- Article
Performance Analysis of Friction Stir Welded Lightweight Aluminum Alloy Sheet.
- Published in:
- Journal of Engineering & Technological Sciences, 2020, v. 52, n. 6, p. 821, doi. 10.5614/j.eng.technol.sci.2020.52.6.4
- By:
- Publication type:
- Article
Reaction Process and Influence of WC Content on Microstructure and Mechanical Properties of Ti(C, N)-Based Cermets.
- Published in:
- Materials Transactions, 2020, n. 11, p. 2149, doi. 10.2320/matertrans.MT-M2020186
- By:
- Publication type:
- Article
Influence of tool offset on microstructure and properties of Mg/Al dissimilar alloys by friction stir welding joints at low heat input.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2020, v. 109, n. 9-12, p. 2845, doi. 10.1007/s00170-020-05788-8
- By:
- Publication type:
- Article
A machining position optimization approach to workpiece deformation control for aeronautical monolithic components.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2020, v. 109, n. 1/2, p. 299, doi. 10.1007/s00170-020-05588-0
- By:
- Publication type:
- Article
The effect of various Co contents on the microstructure and properties of Ti(C,N)-TiB<sub>2</sub>-Co cermets prepared in situ via reactive hot pressing.
- Published in:
- Advances in Mechanical Engineering (Sage Publications Inc.), 2020, v. 12, n. 5, p. 1, doi. 10.1177/1687814020925716
- By:
- Publication type:
- Article
Effect of Pore Defects on Mechanical Properties of Graphene Reinforced Aluminum Nanocomposites.
- Published in:
- Metals (2075-4701), 2020, v. 10, n. 4, p. 468, doi. 10.3390/met10040468
- By:
- Publication type:
- Article
Selective coupling reaction inhibits graphene defects: regulating the orderly precipitation of carbon atoms.
- Published in:
- Applied Nanoscience, 2020, v. 10, n. 2, p. 587, doi. 10.1007/s13204-019-01124-z
- By:
- Publication type:
- Article
Temperature distribution of cubic boron nitride–coated cutting tools by finite element analysis.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2019, v. 105, n. 7/8, p. 3197, doi. 10.1007/s00170-019-04498-0
- By:
- Publication type:
- Article
Effect of rare earth elements on plasma electrolytic carbonitriding of Ti–6Al–4V alloy.
- Published in:
- Materials Science & Technology, 2019, v. 35, n. 18, p. 2275, doi. 10.1080/02670836.2019.1673027
- By:
- Publication type:
- Article
Friction-reducing effect and damage mechanism of laser micro-texture on diamond films during friction.
- Published in:
- Modern Physics Letters B, 2019, v. 33, n. 24, p. N.PAG, doi. 10.1142/S021798491950283X
- By:
- Publication type:
- Article
Design of surface grooves on a polishing pad based on slurry uniform flow.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2019, v. 103, n. 9-12, p. 4795, doi. 10.1007/s00170-019-04026-0
- By:
- Publication type:
- Article
A workpiece stability-based iterative planning of clamping forces for fixturing layout specification of a complex workpiece.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2019, v. 103, n. 5-8, p. 2017, doi. 10.1007/s00170-019-03590-9
- By:
- Publication type:
- Article
Acoustic emission analysis for tool wear state during friction stir joining of SiCp/Al composite.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2018, v. 99, n. 5-8, p. 1361, doi. 10.1007/s00170-018-2565-x
- By:
- Publication type:
- Article
Effect of process parameters on surface topography of friction stir welding.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2018, v. 98, n. 5-8, p. 1807, doi. 10.1007/s00170-018-2326-x
- By:
- Publication type:
- Article
Effect of Processing Parameters and Temperature on Sliding Wear of H62 Copper Alloy Modified by Friction Stir Surface Processing.
- Published in:
- Materials Science / Medziagotyra, 2017, v. 23, n. 3, p. 222, doi. 10.5755/j01.ms.23.3.16322
- By:
- Publication type:
- Article
Self-conditioning performance of hydrophilic fixed abrasive pad.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2017, v. 90, n. 5-8, p. 2217, doi. 10.1007/s00170-016-9553-9
- By:
- Publication type:
- Article
Grinding characteristics in high-speed grinding of boron-diffusion-hardened TC21-DT titanium alloy with vitrified CBN wheel.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2017, v. 89, n. 5-8, p. 1269, doi. 10.1007/s00170-016-9193-0
- By:
- Publication type:
- Article
Effect of chemical additive on fixed abrasive pad self-conditioning in CMP.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2017, v. 88, n. 1-4, p. 107, doi. 10.1007/s00170-016-8771-5
- By:
- Publication type:
- Article
Research of abrasive embedment-free lapping on soft-brittle lithium niobate wafer.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2016, v. 87, n. 5-8, p. 1951, doi. 10.1007/s00170-016-8582-8
- By:
- Publication type:
- Article
Experimental study on multi-layer ice fixed abrasive polishing of single crystal germanium wafer.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2016, v. 85, n. 5-8, p. 1045, doi. 10.1007/s00170-015-8020-3
- By:
- Publication type:
- Article
Low cycle fatigue and strengthening mechanism of cold extruded large diameter internal thread of Q460 steel.
- Published in:
- Chinese Journal of Mechanical Engineering, 2016, v. 29, n. 3, p. 556, doi. 10.3901/CJME.2016.0318.033
- By:
- Publication type:
- Article
Influence of acid slurries on surface quality of LBO crystal in fixed abrasive CMP.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2015, v. 78, n. 1-4, p. 493, doi. 10.1007/s00170-014-6662-1
- By:
- Publication type:
- Article
Experimental Study on Layered Ice Bonded Abrasive Polishing of Glass-ceramics.
- Published in:
- Materials Science / Medziagotyra, 2014, v. 20, n. 4, p. 485, doi. 10.5755/j01.ms.20.4.6149
- By:
- Publication type:
- Article