OTOMOTİV SEKTÖRÜNDE KULLANILAN AZ91 MAGNEZYUM ALAŞIMININ KOROZYON DAYANIMINA ARK PVD SERAMİK FİLM KAPLAMALARIN ETKİSİ.
- Published in:
- SDU International Journal of Technological Sciences, 2018, v. 10, n. 2, p. 1
- By:
- Publication type:
- Article
Works by Yalçın, Bekir
Results: 10
1
2
Microstructural and Mechanical Behavior Investigations of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites.
- Published in:
- Metals (2075-4701), 2023, v. 13, n. 6, p. 1097, doi. 10.3390/met13061097
- By:
- Publication type:
- Article
3
Eriyik yığma modelleme (EYM) ile üretilen çeşitli hücresel yapıların mekanik performanslarının incelenmesi.
- Published in:
- Journal of the Faculty of Engineering & Architecture of Gazi University / Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi,, 2023, v. 38, n. 1, p. 202, doi. 10.17341/gazimmfd.945650
- By:
- Publication type:
- Article
4
4 boyutlu baskı teknolojisi ve uygulama alanlarının araştırılması.
- Published in:
- International Journal of Technological Sciences / Uluslararasi Teknolojik Bilimler Dergisi, 2020, v. 12, n. 3, p. 108
- By:
- Publication type:
- Article
5
Effect of Drilling Parameters and Tool Diameter on Delamination and Thrust Force in the Drilling of High-Performance Glass/Epoxy Composites for Aerospace Structures with a New Design Drill.
- Published in:
- Polymers (20734360), 2024, v. 16, n. 21, p. 3011, doi. 10.3390/polym16213011
- By:
- Publication type:
- Article
6
Co-injection filling characterization of the polypropylen packaging by 3-D simulation.
- Published in:
- Nigde Omer Halisdemir University Journal of Engineering Sciences / Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi, 2022, v. 11, n. 3, p. 806, doi. 10.28948/ngumuh.1083285
- By:
- Publication type:
- Article
7
Optimization of Cutting Parameters to Minimize Wall Deformation in Micro-Milling of Thin-Wall Geometries.
- Published in:
- Micromachines, 2025, v. 16, n. 3, p. 310, doi. 10.3390/mi16030310
- By:
- Publication type:
- Article
8
Effect of Drilling Parameters and Tool Geometry on the Thrust Force and Surface Roughness of Aerospace Grade Laminate Composites.
- Published in:
- Micromachines, 2023, v. 14, n. 7, p. 1427, doi. 10.3390/mi14071427
- By:
- Publication type:
- Article
9
Comparative Analysis of Minimum Chip Thickness, Surface Quality and Burr Formation in Micro-Milling of Wrought and Selective Laser Melted Ti64.
- Published in:
- Micromachines, 2023, v. 14, n. 6, p. 1160, doi. 10.3390/mi14061160
- By:
- Publication type:
- Article
10
Optimization of Micro-Drilling of Laminated Aluminum Composite Panel (Al–PE) Using Taguchi Orthogonal Array Design.
- Published in:
- Materials (1996-1944), 2023, v. 16, n. 13, p. 4528, doi. 10.3390/ma16134528
- By:
- Publication type:
- Article