Creating the Slider Tester Repair Recommendation System to Enhance the Repair Step by Using Machine Learning.
- Published in:
- Machines, 2024, v. 12, n. 9, p. 661, doi. 10.3390/machines12090661
- By:
- Publication type:
- Article
Works matching AU Srisertpol, Jiraphon
Results: 19
1
2
Fault Tolerant Control Based on an Observer on PI Servo Design for a High-Speed Automation Machine.
- Published in:
- Machines, 2020, v. 8, n. 2, p. 22, doi. 10.3390/machines8020022
- By:
- Publication type:
- Article
3
Vibration Reduction of an Overhung Rotor Supported by an Active Magnetic Bearing Using a Decoupling Control System.
- Published in:
- Machines, 2019, v. 7, n. 4, p. 73, doi. 10.3390/machines7040073
- By:
- Publication type:
- Article
4
Fault detection and diagnosis of linear bearing in auto core adhesion mounting machines based on condition monitoring.
- Published in:
- Systems Science & Control Engineering, 2021, v. 9, n. 1, p. 290, doi. 10.1080/21642583.2021.1895901
- By:
- Publication type:
- Article
5
Enhancing the Performance and Durability of Commercial Vehicle Cargo Box Frames through Modal Analysis.
- Published in:
- Applied Sciences (2076-3417), 2023, v. 13, n. 16, p. 9303, doi. 10.3390/app13169303
- By:
- Publication type:
- Article
6
Parameter Optimization of Hole-Slot-Type Magnetron for Controlling Resonant Frequency of Linear Accelerator 6 MeV by Reverse Engineering Technique.
- Published in:
- Applied Sciences (2076-3417), 2021, v. 11, n. 5, p. 2384, doi. 10.3390/app11052384
- By:
- Publication type:
- Article
7
Precision Analysis and Design of Rotating Coil Magnetic Measurements System.
- Published in:
- Applied Sciences (2076-3417), 2020, v. 10, n. 23, p. 8454, doi. 10.3390/app10238454
- By:
- Publication type:
- Article
8
Pyrolysis Oil Derived from Plastic Bottle Caps: Characterization of Combustion and Emissions in a Diesel Engine.
- Published in:
- Energies (19961073), 2023, v. 16, n. 5, p. 2492, doi. 10.3390/en16052492
- By:
- Publication type:
- Article
9
Characterization and Impact of Waste Plastic Oil in a Variable Compression Ratio Diesel Engine.
- Published in:
- Energies (19961073), 2021, v. 14, n. 8, p. 2230, doi. 10.3390/en14082230
- By:
- Publication type:
- Article
10
Evaluation of Waste Plastic Oil-Biodiesel Blends as Alternative Fuels for Diesel Engines.
- Published in:
- Energies (19961073), 2020, v. 13, n. 11, p. 2823, doi. 10.3390/en13112823
- By:
- Publication type:
- Article
11
EXPERIMENTAL INVESTIGATION OF ETHANOL BLENDED WITH WASTE PLASTIC OIL AS AN ALTERNATIVE BIOFUEL IN A DIESEL ENGINE.
- Published in:
- Suranaree Journal of Science & Technology, 2020, v. 27, n. 4, p. 1
- By:
- Publication type:
- Article
12
Electrothermal Dynamics and Electrical Equivalent Circuit Modeling of Li-ion Batteries with NMC, NCA, and LFP Electrode Chemistries.
- Published in:
- International Journal of Intelligent Engineering & Systems, 2024, v. 17, n. 6, p. 284, doi. 10.22266/ijies2024.1231.23
- By:
- Publication type:
- Article
13
Implementation of perspective-n-point techniques and YOLOv5 algorithm based on surveillance camera for localization.
- Published in:
- Indonesian Journal of Electrical Engineering & Computer Science, 2025, v. 37, n. 3, p. 1744, doi. 10.11591/ijeecs.v37.i3.pp1744-1757
- By:
- Publication type:
- Article
14
Optimization signal writing with machine learning assisted control.
- Published in:
- Indonesian Journal of Electrical Engineering & Computer Science, 2025, v. 37, n. 1, p. 90, doi. 10.11591/ijeecs.v37.i1.pp90-100
- By:
- Publication type:
- Article
15
Enhancing testing cell set efficiency: A machine learning approach on hard disk drive data.
- Published in:
- Manufacturing Review, 2024, v. 11, p. 1, doi. 10.1051/mfreview/2024008
- By:
- Publication type:
- Article
16
Using fault detection and classification techniques for machine breakdown reduction of the HGA process caused by the slider loss defect.
- Published in:
- Manufacturing Review, 2022, v. 9, p. 1, doi. 10.1051/mfreview/2022020
- By:
- Publication type:
- Article
17
System modeling and temperature control of reheating furnace walking hearth type in the setting up process.
- Published in:
- Journal of Mechanical Science & Technology, 2014, v. 28, n. 8, p. 3377, doi. 10.1007/s12206-014-0750-x
- By:
- Publication type:
- Article
18
Classifying and Optimizing Spiral Seed Self-Servo Writer Parameters in Manufacturing Process Using Artificial Intelligence Techniques.
- Published in:
- Systems, 2023, v. 11, n. 6, p. 268, doi. 10.3390/systems11060268
- By:
- Publication type:
- Article
19
Optimizing Ultra-High Vacuum Control in Electron Storage Rings Using Fuzzy Control and Estimation of Pumping Speed by Neural Networks with Molflow+.
- Published in:
- Systems, 2023, v. 11, n. 3, p. 116, doi. 10.3390/systems11030116
- By:
- Publication type:
- Article