Found: 18
Select item for more details and to access through your institution.
Cost estimation and performance evaluation of 3D printed membranes for vanadium redox flow batteries.
- Published in:
- Energy Storage (2578-4862), 2024, v. 6, n. 1, p. 1, doi. 10.1002/est2.536
- By:
- Publication type:
- Article
Orientation-Dependent Mechanical Behavior of 3D Printed Polylactic Acid Parts: An Experimental–Numerical Study.
- Published in:
- Machines, 2023, v. 11, n. 12, p. 1086, doi. 10.3390/machines11121086
- By:
- Publication type:
- Article
Optimization through response surface methodology of 3D printed membrane preparation conditions for use in vanadium redox flow battery: A vanadium/proton selectivity study.
- Published in:
- Journal of Applied Polymer Science, 2023, v. 140, n. 35, p. 1, doi. 10.1002/app.54343
- By:
- Publication type:
- Article
Effect of printing parameters on tensile, thermal and structural properties of 3D‐printed poly (ether ketone ketone) PEKK material using fused deposition modeling.
- Published in:
- Journal of Applied Polymer Science, 2023, v. 140, n. 29, p. 1, doi. 10.1002/app.54078
- By:
- Publication type:
- Article
A Combined Experimental and Computational (DFT, RDF, MC and MD) Investigation of Epoxy Resin as a Potential Corrosion Inhibitor for Mild Steel in a 0.5 M H 2 SO 4 Environment.
- Published in:
- Polymers (20734360), 2023, v. 15, n. 8, p. 1967, doi. 10.3390/polym15081967
- By:
- Publication type:
- Article
Investigating the effect of printing conditions and annealing on the porosity and tensile behavior of 3D‐printed polyetherimide material in Z‐direction.
- Published in:
- Journal of Applied Polymer Science, 2023, v. 140, n. 4, p. 1, doi. 10.1002/app.53353
- By:
- Publication type:
- Article
Effects of physical and chemical ageing on 3D printed poly (ether ether ketone)/poly (ether imide) [PEEK/PEI] blend for aerospace applications.
- Published in:
- Journal of Materials Science, 2023, v. 58, n. 3, p. 1465, doi. 10.1007/s10853-022-08068-w
- By:
- Publication type:
- Article
Numerical–Experimental Analysis toward the Strain Rate Sensitivity of 3D-Printed Nylon Reinforced by Short Carbon Fiber.
- Published in:
- Materials (1996-1944), 2022, v. 15, n. 24, p. 8722, doi. 10.3390/ma15248722
- By:
- Publication type:
- Article
Effects of Power and Laser Speed on the Mechanical Properties of AlSi7Mg0.6 Manufactured by Laser Powder Bed Fusion.
- Published in:
- Materials (1996-1944), 2022, v. 15, n. 23, p. 8640, doi. 10.3390/ma15238640
- By:
- Publication type:
- Article
Microinjection molding of polyoxymethylene stepped‐parts: Morphology, crystallinity, shrinkage, and thermal characterization.
- Published in:
- Journal of Applied Polymer Science, 2022, v. 139, n. 39, p. 1, doi. 10.1002/app.52930
- By:
- Publication type:
- Article
Effects of Laser Power and Hatch Orientation on Final Properties of PA12 Parts Produced by Selective Laser Sintering.
- Published in:
- Polymers (20734360), 2022, v. 14, n. 17, p. 3674, doi. 10.3390/polym14173674
- By:
- Publication type:
- Article
Synthesis Characterization and Highly Protective Efficiency of Tetraglycidyloxy Pentanal Epoxy Prepolymer as a Potential Corrosion Inhibitor for Mild Steel in 1 M HCl Medium.
- Published in:
- Polymers (20734360), 2022, v. 14, n. 15, p. 3100, doi. 10.3390/polym14153100
- By:
- Publication type:
- Article
Effects of printing parameters on the tensile behavior of 3D‐printed acrylonitrile styrene acrylate (ASA) material in Z direction.
- Published in:
- Polymer Engineering & Science, 2022, v. 62, n. 3, p. 848, doi. 10.1002/pen.25891
- By:
- Publication type:
- Article
3D Printed and Conventional Membranes—A Review.
- Published in:
- Polymers (20734360), 2022, v. 14, n. 5, p. N.PAG, doi. 10.3390/polym14051023
- By:
- Publication type:
- Article
An Investigation to Study the Effect of Process Parameters on the Strength and Fatigue Behavior of 3D-Printed PLA-Graphene.
- Published in:
- Polymers (20734360), 2021, v. 13, n. 19, p. 3218, doi. 10.3390/polym13193218
- By:
- Publication type:
- Article
Preparation and characterization of poly(ether ether ketone)/poly(ether imide) [PEEK/PEI] blends for fused filament fabrication.
- Published in:
- Journal of Materials Science, 2021, v. 56, n. 25, p. 14348, doi. 10.1007/s10853-021-06172-x
- By:
- Publication type:
- Article
Experimental investigation and optimization of printing parameters of 3D printed polyphenylene sulfide through response surface methodology.
- Published in:
- Journal of Applied Polymer Science, 2021, v. 138, n. 1, p. 1, doi. 10.1002/app.49625
- By:
- Publication type:
- Article
Optimization of printing parameters for improvement of mechanical and thermal performances of 3D printed poly(ether ether ketone) parts.
- Published in:
- Journal of Applied Polymer Science, 2020, v. 137, n. 37, p. 1, doi. 10.1002/app.49087
- By:
- Publication type:
- Article