A fast iron loss calculation model for switched reluctance motors.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 478, doi. 10.1049/iet-epa.2016.0808
- By:
- Publication type:
- Article
Works matching IS 17518660 AND DT 2017 AND VI 11 AND IP 3
Results: 20
1
2
No‐load losses based method to detect demagnetisation fault in permanent magnet synchronous motors with parallel branches.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 471, doi. 10.1049/iet-epa.2016.0625
- By:
- Publication type:
- Article
3
Two‐phase high‐performance control of a reliable stand‐alone induction generator.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 460, doi. 10.1049/iet-epa.2016.0686
- By:
- Publication type:
- Article
4
Effective and simplified method in maximum efficiency control of interior permanent magnet synchronous motors.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 447, doi. 10.1049/iet-epa.2016.0617
- By:
- Publication type:
- Article
5
Calculation of mutual inductance and magnetic force between two thick coaxial Bitter coils of rectangular cross section.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 441, doi. 10.1049/iet-epa.2016.0628
- By:
- Publication type:
- Article
6
Modelling and analysis of PPF in PMSM.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 434, doi. 10.1049/iet-epa.2016.0624
- By:
- Publication type:
- Article
7
Transient current limiter for suppressing transformer inrush, motor starting and fault currents in power system.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 423, doi. 10.1049/iet-epa.2016.0190
- By:
- Publication type:
- Article
8
Proposed diagnostic methodology using the cross‐correlation coefficient factor technique for power transformer fault identification.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 412, doi. 10.1049/iet-epa.2016.0545
- By:
- Publication type:
- Article
9
Phase current reconstruction strategy for switched reluctance machines with fault‐tolerant capability.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 399, doi. 10.1049/iet-epa.2016.0567
- By:
- Publication type:
- Article
10
Influence of parameters of cap‐lamination secondaries on performances in single‐sided linear induction motors.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 393, doi. 10.1049/iet-epa.2016.0678
- By:
- Publication type:
- Article
11
Investigation of electrification and breakdown strength about transformer oil/pressboard.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 386, doi. 10.1049/iet-epa.2016.0706
- By:
- Publication type:
- Article
12
Optimal design of motor shape and magnetisation direction to obtain vibration reduction and average torque improvement in IPM BLDC motor.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 378, doi. 10.1049/iet-epa.2016.0618
- By:
- Publication type:
- Article
13
Analytical method for levitation force calculation of radial HTS magnetic bearings.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 369, doi. 10.1049/iet-epa.2016.0070
- By:
- Publication type:
- Article
14
Piecewise variable parameter model for precise analysis of iron losses in induction motors.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 361, doi. 10.1049/iet-epa.2016.0009
- By:
- Publication type:
- Article
15
Switched reluctance motor drive from an AC supply.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 352, doi. 10.1049/iet-epa.2016.0477
- By:
- Publication type:
- Article
16
Analytical, numerical and experimental analysis of induction heating of graphite crucible for melting of non‐magnetic materials.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 342, doi. 10.1049/iet-epa.2016.0393
- By:
- Publication type:
- Article
17
Active torque ripple reduction based on an analytical model of torque.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 331, doi. 10.1049/iet-epa.2016.0475
- By:
- Publication type:
- Article
18
Modelling the low‐frequency dielectric response test of insulation oil.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 323, doi. 10.1049/iet-epa.2016.0673
- By:
- Publication type:
- Article
19
Analytical modelling and prototyping a slotless surface‐inset PM machine.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 312, doi. 10.1049/iet-epa.2016.0402
- By:
- Publication type:
- Article
20
Computationally efficient calculation of skew effects in brushless doubly‐fed induction machines.
- Published in:
- IET Electric Power Applications (Wiley-Blackwell), 2017, v. 11, n. 3, p. 303, doi. 10.1049/iet-epa.2016.0354
- By:
- Publication type:
- Article