Works matching IS 12299138 AND DT 2011 AND VI 12 AND IP 6

Results: 18

Reliability-based topology optimization based on bidirectional evolutionary structural optimization using multi-objective sensitivity numbers.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 849, doi. 10.1007/s12239-011-0097-6

By:

Cho, K.;
Park, J.;
Ryu, S.;
Han, S.

Publication type:

Article

Large-eddy simulation of air entrainment during diesel spray combustion with multi-dimensional CFD.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 795, doi. 10.1007/s12239-011-0092-y

By:

Azimov, U.;
Kim, K.

Publication type:

Article

Advance-F automatic car-following model and its traffic characteristics.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 933, doi. 10.1007/s12239-011-0106-9

By:

Chang, T.;
Wang, M.;
Yu, S.

Publication type:

Article

Optimization and design of disk-type MR brakes.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 921, doi. 10.1007/s12239-011-0105-x

By:

Assadsangabi, B.;
Daneshmand, F.;
Vahdati, N.;
Eghtesad, M.;
Bazargan-Lari, Y.

Publication type:

Article

Neural-empirical tyre model based on recursive lazy learning under combined longitudinal and lateral slip conditions.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 821, doi. 10.1007/s12239-011-0094-9

By:

Boada, M.;
Boada, B.;
Garcia-Pozuelo, D.;
Diaz, V.

Publication type:

Article

Lateral dynamics of single unit skid-steered tracked vehicle.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 865, doi. 10.1007/s12239-011-0099-4

By:

Janarthanan, B.;
Padmanabhan, C.;
Sujatha, C.

Publication type:

Article

Model development and experimental research on an air spring with auxiliary reservoir.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 839, doi. 10.1007/s12239-011-0096-7

By:

Liu, H.;
Lee, J.

Publication type:

Article

Model referenced adaptive control to compensate slip-stick transition during clutch engagement.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 913, doi. 10.1007/s12239-011-0104-y

By:

Chen, L.;
Xi, G.;
Yin, C.

Publication type:

Article

Direct method for optimal power management in hybrid electric vehicles.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 943, doi. 10.1007/s12239-011-0107-8

By:

Dosthosseini, R.;
Kouzani, A.;
Sheikholeslam, F.

Publication type:

Article

Development of hot stamped center pillar using form die with channel type indirect blank holder.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 887, doi. 10.1007/s12239-011-0101-1

By:

Choi, H.;
Kim, B.;
Nam, K.;
Ha, S.;
Cha, S.;
Kang, C.

Publication type:

Article

Method to objectively evaluate subjective ratings of ride comfort.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 831, doi. 10.1007/s12239-011-0095-8

By:

Kim, M.;
Kim, K.;
Yoo, W.

Publication type:

Article

Experimental evaluation of SOF effects on EGR cooler fouling under various flow conditions.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 813, doi. 10.1007/s12239-011-0093-x

By:

Hong, K.;
Park, J.;
Lee, K.

Publication type:

Article

Active controller design for an electromagnetic energy-regenerative suspension.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 877, doi. 10.1007/s12239-011-0100-2

By:

Huang, K.;
Yu, F.;
Zhang, Y.

Publication type:

Article

Combustion instabilities and nanoparticles emission fluctuations in GDI spark ignition engine.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 787, doi. 10.1007/s12239-011-0091-z

By:

Hassaneen, A.;
Samuel, S.;
Whelan, I.

Publication type:

Article

Approach to assess a fast welding simulation in an industrial environment - Application for an automotive welded part.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 895, doi. 10.1007/s12239-011-0102-0

By:

Perret, W.;
Thater, R.;
Alber, U.;
Schwenk, C.;
Rethmeier, M.

Publication type:

Article

Relationship between occupant injury and the perturbation mark on the velocity indicator on a cluster panel.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 951, doi. 10.1007/s12239-011-0108-7

By:

Kim, S.;
Jeon, W.;
Park, J.;
Moon, B.;
Cho, Y.;
Seo, Y.;
Park, N.;
Son, K.

Publication type:

Article

Numerical and experimental investigation of lubricating oil flow in a gerotor pump.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 903, doi. 10.1007/s12239-011-0103-z

By:

Suresh Kumar, M.;
Manonmani, K.

Publication type:

Article

Objectification of on-center handling characteristics based on spring-mass-damper system.

Published in:

International Journal of Automotive Technology, 2011, v. 12, n. 6, p. 857, doi. 10.1007/s12239-011-0098-5

By:

Kim, J.

Publication type:

Article