Correction to: Effect of Porosity Parameters on the Strength of Gas Turbine Compressor Blades Made of Titanium Alloys.
- Published in:
- 2020
- By:
- Publication type:
- Correction Notice
Works matching IS 00392316 AND DT 2020 AND VI 52 AND IP 1
Results: 21
1
2
Correction to: Effect of Shock and Vibration Preloading on the Parameters of Tear Dimples and Their Conglomerates.
- Published in:
- 2020
- By:
- Publication type:
- Correction Notice
3
Bayesian Estimation of Constant-Stress Life Test Model Using Type-I Censored Data from the Linear Failure Rate Distribution.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 171, doi. 10.1007/s11223-020-00162-1
- By:
- Publication type:
- Article
4
Vibration Analysis of a Three-Drum Shearer for a Large Mining Height.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 160, doi. 10.1007/s11223-020-00161-2
- By:
- Publication type:
- Article
5
Reflective Cracking Resistance Improvement of the Asphalt Concrete Overlay on an Airfield Pavement.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 149, doi. 10.1007/s11223-020-00160-3
- By:
- Publication type:
- Article
6
Evaluation of Compression Strength of Concrete Specimens via Experimental Results and Numerical Simulation.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 138, doi. 10.1007/s11223-020-00159-w
- By:
- Publication type:
- Article
7
Effect of Surface Protection on the Strength Properties and Frost Resistance of Hydraulic Concrete.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 130, doi. 10.1007/s11223-020-00158-x
- By:
- Publication type:
- Article
8
Tribological Behavior of AISI52100 Steel After PC/MoS2 Lubricant Surface Modification.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 118, doi. 10.1007/s11223-020-00157-y
- By:
- Publication type:
- Article
9
Assessment of the Fatigue Cracking Impact and Optimization of Operating Conditions of a Hydraulic Hammer Anvil.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 110, doi. 10.1007/s11223-020-00156-z
- By:
- Publication type:
- Article
10
A Co–Cr–Ni–W–C Alloy Processed by Multiple Rolling.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 103, doi. 10.1007/s11223-020-00155-0
- By:
- Publication type:
- Article
11
Simulation of the Crack Geometry Effect on the Natural Vibration Frequency of a Plate Blade.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 97, doi. 10.1007/s11223-020-00154-1
- By:
- Publication type:
- Article
12
Warping of a Stretched Bimetallic Sheet.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 90, doi. 10.1007/s11223-020-00153-2
- By:
- Publication type:
- Article
13
Milling-Related Brittle Fracture Mechanisms of a SiCp/Al Composite.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 81, doi. 10.1007/s11223-020-00152-3
- By:
- Publication type:
- Article
14
Structural and Mechanical Characteristics of AISI 420 Stainless Steel After Annealing.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 71, doi. 10.1007/s11223-020-00151-4
- By:
- Publication type:
- Article
15
Circumferential Sealing Structure of a Subsea Oil and Gas Pipeline Repair Clamp.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 59, doi. 10.1007/s11223-020-00150-5
- By:
- Publication type:
- Article
16
Effect of the Stir Rotation Speed on the Microstructure and Properties of Super304H/T92 Friction Weld Joints.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 51, doi. 10.1007/s11223-020-00149-y
- By:
- Publication type:
- Article
17
Effect of the Second-Phase Particle Precipitation on the Recrystallization Texture of High-Strength and Fine-Grain Interstitial-Free Steel.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 40, doi. 10.1007/s11223-020-00148-z
- By:
- Publication type:
- Article
18
Mechanical Behavior and Formability of Quench and Partition Steel Sheets.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 32, doi. 10.1007/s11223-020-00147-0
- By:
- Publication type:
- Article
19
Numerical Simulation of the Temperature and Stress State on the Additive Friction Stir with the Smoothed Particle Hydrodynamics Method.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 24, doi. 10.1007/s11223-020-00146-1
- By:
- Publication type:
- Article
20
Verification of Dislocation Density and Dynamic Recrystallization in Deformed Pure Copper.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 16, doi. 10.1007/s11223-020-00145-2
- By:
- Publication type:
- Article
21
Fatigue Life Enhancement of a D16at Aluminum Alloy for Aircraft Components with Fastener Holes.
- Published in:
- Strength of Materials, 2020, v. 52, n. 1, p. 1, doi. 10.1007/s11223-020-00144-3
- By:
- Publication type:
- Article