Works matching IS 02683768 AND DT 2020 AND VI 110 AND IP 11/12

Results: 41

A machinability evaluation based on the thermal and mechanical properties of two engine valve steels.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3209, doi. 10.1007/s00170-020-06108-w

By:

Carvalho, Marta Regina Delle Donne;
Antonialli, Armando Ítalo Sette;
Diniz, Anselmo Eduardo

Publication type:

Article

State of the art on internal thread manufacturing: a review.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3445, doi. 10.1007/s00170-020-06107-x

By:

Brandão, Guilherme Lopes;
Silva, Pedro Márcio do Carmo;
de Freitas, Samuel Alves;
Pereira, Robson Bruno Dutra;
Lauro, Carlos Henrique;
Brandão, Lincoln Cardoso

Publication type:

Article

Deformation and control method of thin-walled part during laser powder bed fusion of Ti–6Al–4V alloy.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3467, doi. 10.1007/s00170-020-06104-0

By:

Chen, Changpeng;
Xiao, Zhongxu;
Zhu, Haihong;
Zeng, Xiaoyan

Publication type:

Article

A feasible strategy to produce quality holes using temperature-assisted drilling on CFRP.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3113, doi. 10.1007/s00170-020-06089-w

By:

John, K. M.;
Kumaran, S. Thirumalai

Publication type:

Article

Influence of forging velocity on temperature and phase transformation characteristics of forged Ti-6Al-4V aeroengine drum.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3101, doi. 10.1007/s00170-020-06084-1

By:

Luo, Shiyuan;
Yao, Junning;
Zou, Guangming;
Li, Jia;
Jiang, Jun;
Yu, Fengping

Publication type:

Article

Influence of micro-structured milling cutter on the milling load and surface roughness of 6061 aluminum alloy.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3201, doi. 10.1007/s00170-020-06080-5

By:

Pan, Jianfeng;
Ni, Jing;
He, Lihua;
Cui, Zhi;
Feng, Kai

Publication type:

Article

Additive manufacturing in fighting against novel coronavirus COVID-19.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2913, doi. 10.1007/s00170-020-06077-0

By:

Tarfaoui, M.;
Nachtane, M.;
Goda, I.;
Qureshi, Y.;
Benyahia, H.

Publication type:

Article

Laser texturing of AISI 304 stainless steel: experimental analysis and genetic algorithm optimisation to control the surface wettability.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3005, doi. 10.1007/s00170-020-06073-4

By:

Genna, Silvio;
Giannini, Oliviero;
Guarino, Stefano;
Ponticelli, Gennaro Salvatore;
Tagliaferri, Flaviana

Publication type:

Article

Erosion wear behavior of spark plasma-sintered Ti-6Al-4V reinforced with TiN nanoparticles.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3051, doi. 10.1007/s00170-020-06072-5

By:

Kganakga, Mokgoba Glodean;
Prieto, German;
Falodun, Oluwasegun Eso;
Tuckart, Walter R.;
Obadele, Babatunde Abiodun;
Ajibola, Olarewaju Olawale;
Olubambi, Peter Apata

Publication type:

Article

Vacuum laser powder bed fusion—track consolidation, powder denudation, and future potential.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3339, doi. 10.1007/s00170-020-06071-6

By:

Kaserer, L.;
Bergmueller, S.;
Braun, J.;
Leichtfried, G.

Publication type:

Article

Effects of reinforcements and cutting parameters on machinability of polypropylene-based biocomposite reinforced with biocarbon particles and chopped miscanthus fibers.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3423, doi. 10.1007/s00170-020-06070-7

By:

Tran, Dinh Son;
Songmene, Victor;
Ngo, Anh Dung;
Kouam, Jules

Publication type:

Article

Cooling of motor spindles—a review.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3273, doi. 10.1007/s00170-020-06069-0

By:

Denkena, Berend;
Bergmann, Benjamin;
Klemme, Heinrich

Publication type:

Article

Estimation of average roughness of X200Cr12 steel using displacement from the tool nozzle.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3323, doi. 10.1007/s00170-020-06067-2

By:

Kribes, N.;
Rezaiguia, A.;
Ouelaa, N.;
Yallese, M.A.

Publication type:

Article

Effective and efficient removing method of micromolds in UV-LIGA using CO2 laser ablation followed by O2/CF4 plasma finishing for high-aspect-ratio metallic microstructures.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3391, doi. 10.1007/s00170-020-06065-4

By:

Han, Dong;
Yoshida, Kazuhiro;
Kim, Joon-wan

Publication type:

Article

Using inverse replica fixture technique for improving nano-finishing of hip joint implant in abrasive flow finishing process.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3035, doi. 10.1007/s00170-020-06064-5

By:

Choopani, Yahya;
Khajehzadeh, Mohsen;
Razfar, Mohammad Reza

Publication type:

Article

Patch and curvature specific estimation of efficient sampling scheme for complex surface inspection.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3407, doi. 10.1007/s00170-020-06063-6

By:

Abdulhameed, Osama;
Mian, Syed Hammad;
Al-Ahmari, Abdulrahman;
Alkhalefah, Hisham

Publication type:

Article

Hybrid manufacturing: a review of the synergy between directed energy deposition and subtractive processes.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3377, doi. 10.1007/s00170-020-06062-7

By:

Dávila, José Luis;
Neto, Paulo Inforçatti;
Noritomi, Pedro Yoshito;
Coelho, Reginaldo Teixeira;
da Silva, Jorge Vicente Lopes

Publication type:

Article

Correction to: Automatic monitoring of steel strip positioning error based on semantic segmentation.

Published in:

2020

By:

Lemos, Aline de Faria;
da Silva, Leonardo Adolpho Rodrigues;
Nagy, Balázs Vince

Publication type:

Correction Notice

A review on cutting tool technology in machining of Ni-based superalloys.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2863, doi. 10.1007/s00170-020-06052-9

By:

Fan, Wei;
Ji, Wei;
Wang, Lihui;
Zheng, Lianyu;
Wang, Yahui

Publication type:

Article

Improved cross pattern approach for steel surface defect recognition.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3091, doi. 10.1007/s00170-020-06050-x

By:

Mentouri, Zoheir;
Doghmane, Hakim;
Moussaoui, Abdelkrim;
Bourouba, Hocine

Publication type:

Article

A smart tool wear prediction model in drilling of woven composites.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2881, doi. 10.1007/s00170-020-06049-4

By:

Hegab, H.;
Hassan, M.;
Rawat, S.;
Sadek, A.;
Attia, H.

Publication type:

Article

Real-time discrete event simulation: a framework for an intelligent expert system approach utilising decision trees.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2893, doi. 10.1007/s00170-020-06048-5

By:

Prajapat, N.;
Turner, C.;
Tiwari, A.;
Tiwari, D.;
Hutabarat, W.

Publication type:

Article

Gaussian approach–based cutting force coefficient identification for flat-end milling operation.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3023, doi. 10.1007/s00170-020-06045-8

By:

Soni, Dhrumil;
Desai, K. A.

Publication type:

Article

Surface roughness modeling using response surface methodology and a variant of multiquadric radial basis function.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3311, doi. 10.1007/s00170-020-06035-w

By:

Sánchez-López, Orquídea;
Hernández-Castillo, Ignacio;
Castañeda-Roldán, Cuauhtémoc-Héctor;
Santiago-Alvarado, Agustin;
Cruz-Félix, Angel-Sinue

Publication type:

Article

An approach for performance evaluation of SBS/RS with shuttle vehicles serving multiple tiers of multiple-deep storage rack.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3241, doi. 10.1007/s00170-020-06033-y

By:

Eder, Michael

Publication type:

Article

Thermomechanical processing of an ultralight Mg-14Li-1Al alloy.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3221, doi. 10.1007/s00170-020-06032-z

By:

Islam, Rezawana;
Hadadzadeh, Amir;
Wells, Mary;
Haghshenas, Meysam

Publication type:

Article

Experimental study on high-speed saw cutting of hybrid composite stacks using nanoparticle-enhanced minimum quantity lubrication.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3077, doi. 10.1007/s00170-020-06008-z

By:

James, Sagil;
Nejadian, Shayan Mohammad

Publication type:

Article

Deformation behavior of steel-to-aluminum tailor blanks made by laser/MIG hybrid and cold metal transfer brazing methods.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3061, doi. 10.1007/s00170-020-06003-4

By:

Shaker, M. A.;
Jain, M. K.;
Chen, J. Z.

Publication type:

Article

A novel image feature descriptor for SLM spattering pattern classification using a consumable camera.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2955, doi. 10.1007/s00170-020-05995-3

By:

Ji, Ze;
Han, Quanquan

Publication type:

Article

A three-stage quality diagnosis platform for laser-based manufacturing processes.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2991, doi. 10.1007/s00170-020-05981-9

By:

Stavropoulos, Panagiotis;
Papacharalampopoulos, Alexios;
Stavridis, John;
Sampatakakis, Kyriakos

Publication type:

Article

Recent development of improved clinching process.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3169, doi. 10.1007/s00170-020-05978-4

By:

Peng, Hao;
Chen, Chao;
Zhang, Huiyang;
Ran, Xiangkun

Publication type:

Article

Rapid calibration method for measuring linear axis optical paths of computer numerical control machine tools with a laser interferometer.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3347, doi. 10.1007/s00170-020-05976-6

By:

Jiang, Xiaogeng;
Meng, Tianfang;
Wang, Liang;
Liu, Chang

Publication type:

Article

A collaborative optimization method of machining sequence for deformation control of double-sided structural parts.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2941, doi. 10.1007/s00170-020-05968-6

By:

Hao, Xiaozhong;
Li, Yingguang;
Ni, Yang;
Li, Mengqiu;
Liu, Changqing

Publication type:

Article

Research on automatic monitoring method of face milling cutter wear based on dynamic image sequence.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3365, doi. 10.1007/s00170-020-05955-x

By:

Qin, Aoping;
Guo, Liang;
You, Zhichao;
Gao, Hongli;
Wu, Xiangdong;
Xiang, Shoubing

Publication type:

Article

Precision forward design for 3D printing using kinematic sensitivity via Jacobian matrix considering uncertainty.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3257, doi. 10.1007/s00170-020-05940-4

By:

Jinghua, Xu;
Xueqing, Feng;
Jun, Cen;
Shuyou, Zhang

Publication type:

Article

Generating micro grooves with a semicircular cross-section using wire electrochemical micromachining.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2929, doi. 10.1007/s00170-020-05934-2

By:

Zhou, Zhongqi;
Fang, Xiaolong;
Zeng, Yongbin;
Zhu, Di

Publication type:

Article

Influence of filler metal on residual stress in multi-pass repair welding of thick P91 steel pipe.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2977, doi. 10.1007/s00170-020-05921-7

By:

Guo, Qinghu;
Du, Baoshuai;
Xu, Guoxiang;
Chen, Donggao;
Ma, Liangchao;
Wang, Dafeng;
Zhang, Yingying

Publication type:

Article

Development of a cylindrical coordinate-based fused filament fabrication machine with multiple print heads.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3129, doi. 10.1007/s00170-020-05900-y

By:

Monteiro, Diogo Líbano;
Vicente, Carlos Miguel Santos;
de Oliveira Leite, Marco Alexandre;
Ribeiro, António Manuel Relógio

Publication type:

Article

Smoothing method of generating flank milling tool paths for five-axis flat-end machining considering constraints.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3295, doi. 10.1007/s00170-020-05880-z

By:

Lu, Yao-An;
Wang, Cheng-Yong

Publication type:

Article

Automatic monitoring of steel strip positioning error based on semantic segmentation.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 2847, doi. 10.1007/s00170-020-05859-w

By:

Lemos, Aline de Faria;
da Silva, Leonardo Adolpho Rodrigues;
Nagy, Balázs Vince

Publication type:

Article

Improving the surface quality of friction stir welds using reinforcement learning and Bayesian optimization.

Published in:

International Journal of Advanced Manufacturing Technology, 2020, v. 110, n. 11/12, p. 3145, doi. 10.1007/s00170-020-05696-x

By:

Hartl, R.;
Hansjakob, J.;
Zaeh, M. F.

Publication type:

Article