Development of an intelligent process model for EDM.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 300, doi. 10.1007/s00170-009-1972-4
- By:
- Publication type:
- Article
Works matching IS 02683768 AND DT 2010 AND VI 45 AND IP 3/4
Results: 19
1
2
Cause-selecting control charts based on Huber’s M-estimator.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 341, doi. 10.1007/s00170-009-1966-2
- By:
- Publication type:
- Article
3
Flange forming with combined blanking and extrusion process on sheet metals by FEM and experiments.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 234, doi. 10.1007/s00170-009-1965-3
- By:
- Publication type:
- Article
4
Single-machine scheduling with a sum-of-processing-time based learning effect and deteriorating jobs.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 336, doi. 10.1007/s00170-009-1950-x
- By:
- Publication type:
- Article
5
A linear piezo-electric ultrasonic motor using a single flexural vibrating bar for electro-discharge system industrial applications.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 287, doi. 10.1007/s00170-009-1955-5
- By:
- Publication type:
- Article
6
Development of a continuous fabrication system for a metallic sandwich plate with a three-dimensional truss core.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 352, doi. 10.1007/s00170-009-1964-4
- By:
- Publication type:
- Article
7
A method to exchange the demand of products for cost improvement.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 382, doi. 10.1007/s00170-009-1959-1
- By:
- Publication type:
- Article
8
Direct milling of polymethylmethacrylate for cranioplasty applications.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 318, doi. 10.1007/s00170-009-1978-y
- By:
- Publication type:
- Article
9
Research on thermal stress, deformation, and fatigue lifetime of the rapid heating cycle injection mold.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 261, doi. 10.1007/s00170-009-1969-z
- By:
- Publication type:
- Article
10
Complex nonlinear behaviors of drilling shaft system in boring and trepanning association deep hole drilling.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 211, doi. 10.1007/s00170-009-1961-7
- By:
- Publication type:
- Article
11
Finite element simulation of earing defect in deep drawing.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 219, doi. 10.1007/s00170-009-1963-5
- By:
- Publication type:
- Article
12
Optimization of delamination factor in drilling medium-density fiberboards (MDF) using desirability-based approach.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 370, doi. 10.1007/s00170-009-1974-2
- By:
- Publication type:
- Article
13
An efficient approximate profiling method for the rack gear tool.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 326, doi. 10.1007/s00170-009-1957-3
- By:
- Publication type:
- Article
14
A case-based and practical approach for multivariate modeling of grinding process.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 245, doi. 10.1007/s00170-009-1977-z
- By:
- Publication type:
- Article
15
Multi-response optimisation of sintering parameters of Al–Si alloy/fly ash composite using Taguchi method and grey relational analysis.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 362, doi. 10.1007/s00170-009-1973-3
- By:
- Publication type:
- Article
16
Application of PCA-based hybrid Taguchi method for correlated multicriteria optimization of submerged arc weld: a case study.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 276, doi. 10.1007/s00170-009-1976-0
- By:
- Publication type:
- Article
17
Direct minimal empty siphon computation using MIP.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 397, doi. 10.1007/s00170-009-1967-1
- By:
- Publication type:
- Article
18
A general fuzzy TOPSIS model in multiple criteria decision making.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 406, doi. 10.1007/s00170-009-1971-5
- By:
- Publication type:
- Article
19
Multi-objectives optimal model of heavy equipment using improved Strength Pareto Evolutionary Algorithm.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2010, v. 45, n. 3/4, p. 389, doi. 10.1007/s00170-009-1962-6
- By:
- Publication type:
- Article