A bicriteria parallel machine scheduling with a learning effect.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1202, doi. 10.1007/s00170-008-1436-2
- By:
- Publication type:
- Article
Works matching IS 02683768 AND DT 2009 AND VI 40 AND IP 11/12
Results: 21
1
2
Design and experimental study of a power supply for micro-wire EDM.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1111, doi. 10.1007/s00170-008-1431-7
- By:
- Publication type:
- Article
3
In-cycle monitoring of tool nose wear and surface roughness of turned parts using machine vision.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1148, doi. 10.1007/s00170-008-1430-8
- By:
- Publication type:
- Article
4
Notch wear detection in cutting tools using gradient approach and polynomial fitting.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1057, doi. 10.1007/s00170-008-1437-1
- By:
- Publication type:
- Article
5
Study on LD-VHDL conversion for FPGA-based PLC implementation.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1181, doi. 10.1007/s00170-008-1426-4
- By:
- Publication type:
- Article
6
A study of lead time variation impact on supply chain performance.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1206, doi. 10.1007/s00170-008-1428-2
- By:
- Publication type:
- Article
7
A hybridized approach to optimal tolerance synthesis of clutch assembly.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1118, doi. 10.1007/s00170-008-1418-4
- By:
- Publication type:
- Article
8
Influence of electrical conditions on performance of electrical discharge machining with powder suspended in working oil for titanium carbide deposition process.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1093, doi. 10.1007/s00170-008-1420-x
- By:
- Publication type:
- Article
9
Optimisation of multiple responses for WEDM processes using weighted principal components.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1102, doi. 10.1007/s00170-008-1429-1
- By:
- Publication type:
- Article
10
The effect of die/blank holder and punch radiuses on limit drawing ratio in angular deep-drawing dies.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1077, doi. 10.1007/s00170-008-1435-3
- By:
- Publication type:
- Article
11
A novel depth-from-focus-based measurement system for the reconstruction of surface morphology with depth discontinuity.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1158, doi. 10.1007/s00170-008-1438-0
- By:
- Publication type:
- Article
12
Model for surface-roughness parameters determination in a virtual machine shop environment.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1137, doi. 10.1007/s00170-008-1441-5
- By:
- Publication type:
- Article
13
Roughness modeling and optimization in CNC end milling using response surface method: effect of workpiece material variation.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1166, doi. 10.1007/s00170-008-1440-6
- By:
- Publication type:
- Article
14
An intelligent sampling method for inspecting free-form surfaces.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1125, doi. 10.1007/s00170-008-1427-3
- By:
- Publication type:
- Article
15
A band-type network model for the time-series problem used for IC leadframe dam-bar shearing process.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1252, doi. 10.1007/s00170-008-1432-6
- By:
- Publication type:
- Article
16
Bicriteria scheduling of a two-machine flowshop with sequence-dependent setup times.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1216, doi. 10.1007/s00170-008-1439-z
- By:
- Publication type:
- Article
17
An artificial neural network approach to multiple-response optimization.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1227, doi. 10.1007/s00170-008-1423-7
- By:
- Publication type:
- Article
18
A comprehensive study on the free vibration of machine tools’ hexapod table.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1239, doi. 10.1007/s00170-008-1433-5
- By:
- Publication type:
- Article
19
Feedrate scheduling strategy for free-form surface machining through an integrated geometric and mechanistic model.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1191, doi. 10.1007/s00170-008-1424-6
- By:
- Publication type:
- Article
20
On the temperature field during superficial grinding: an experimental study.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1084, doi. 10.1007/s00170-008-1442-4
- By:
- Publication type:
- Article
21
Influence of friction during forming processes—a study using a numerical simulation technique.
- Published in:
- International Journal of Advanced Manufacturing Technology, 2009, v. 40, n. 11/12, p. 1067, doi. 10.1007/s00170-008-1425-5
- By:
- Publication type:
- Article